User manual ONKYO SL-107

[. . . ] When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over. S3125A Unplug this apparatus during lightning storms or when unused for long periods of time. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. Damage Requiring Service Unplug the apparatus from the wall outlet and refer servicing to qualified service personnel under the following conditions: A. [. . . ] Make sure that the voltage in your area meets the voltage requirements printed on the SL-107's rear panel (AC 220­230 V, 50/60 Hz). 5. Placement · The enclosure is made of wood and is therefore sensitive to extreme temperatures and humidity. Avoid placing the unit in locations subject to direct sunlight or in humid places, such as near an air conditioner, bathroom or kitchen, as well as in locations subject to soot or steam, such as near a kitchen table or humidifier. If water is spilled into the unit, not only the unit but also the connected amplifier (or receiver) may be damaged. · Place the unit on a level and rigid surface free from vibration. If the SL-107 is to be placed on flooring or other similar surfaces, attach these spacers to the bottom surface at the corners. This will not only prevent scratching, but also provide a stable footing. However, note that depending on the surface, the spacers may leave markings. · This unit is designed to be used in an upright vertical position only. · If the unit is used near a turntable or CD player, feedback or skipping of sound may occur. To prevent this, move the unit away from the turntable or CD player or otherwise lower the unit's output level. En-2 Features · This subwoofer system is equipped with a built-in amplifier solely for the reproduction of the superbass range. · With the built-in left-right mixing circuit and cut-off filter, you can simply connect the unit to your existing system to enjoy powerful bass reproduction. Contents Important Safety Instructions . . . . . . . 8 Supplied Accessories · Pin connector cable · Cork spacers (4 pcs. ) Using cork spacers with SL-107 We recommend using the provided cork spacers to achieve the best possible sound from your speaker. The cork spacers prevent the speaker from moving, providing a more stable setup. Cork spacer Bottom of the SL-107 Declaration of Conformity We, ONKYO EUROPE ELECTRONICS GmbH LIEGNITZERSTRASSE 6, 82194 GROEBENZELL, GERMANY declare in own responsibility, that the ONKYO product described in this instruction manual is in compliance with the corresponding technical standards such as EN60065, EN55013, EN55020 and EN61000-3-2, -3-3. MORI ONKYO EUROPE ELECTRONICS GmbH En-3 Controls FRONT VIEW REAR PANEL PHASE 1 STANDBY/ON 3 OUTPUT LEVEL FREQUENCY NOR REV 4 L R 2 LINE INPUT (MONO) C SPEAKER LEVEL INPUT OUTPUT FROM AMP/RECEIVER TO SPEAKERS L L A R R B POWER OFF ON 5 To AC outlet 1 Standby/On indicator (STANDBY/ON) This indicator lights up when the power switch is set to the ON position. Red: The unit is in Standby mode Green: The unit is in Operational mode If the power is turned on, the SL-107 automatically enters Operational mode when a signal is input. The SL-107 automatically returns to Standby mode when no signal has been input for about 20 minutes. FREQUENCY knob Use this knob to select the high-frequency range at which to cut off the signal to the subwoofer. You can select any frequency between 50 Hz and 200 Hz, depending on the characteristics of the speaker system. Depending on the connected speakers or the installation environment of the SL-107 however, the "REV" position may result in better sound. OUTPUT LEVEL knob Use this knob to adjust the output level of the subwoofer. POWER switch Press this switch to the ON position to turn on the power. [. . . ] · The speaker setting at the amplifier (or receiver) is incorrect. Slightly increase the output level at the amplifier (or receiver) (see page 5). · The input signal is so small that the unit entered Standby mode. Turn the OUTPUT LEVEL knob until the Standby/On indicator light is green. [. . . ]