User manual ONKYO T-4030

[. . . ] Contents DAB/FM Tuner Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . En-2 T-4030 Instruction Manual Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new Tuner. Please retain this manual for future reference. Appendix Troubleshooting . . . . . . . . . . . . . . . . . . . . . [. . . ] Note: • If the T-4030 is used with another Onkyo component, refer to its instruction manual as well. Digital (Optical or Coaxial) Connection T-4030 Connect either of them. Amplifier Use the digital audio cable to connect the T-4030’s DIGITAL COAXIAL/OPTICAL jacks to the DIGITAL IN jacks on your amplifier, as shown. En-12 Connecting Your Components—Continued Connecting Onkyo R Components If you connect the T-4030 to another Onkyo R-capable component with the supplied R cable and audio cable, you can use the following system functions. Auto Power On When you turn on the T-4030, your Onkyo amplifier will turn on automatically. (The amplifier’s POWER switch must be set to ON for this to work. ) Direct Change When you select a radio preset or change the band (FM, DAB), your Onkyo amplifier will automatically select the T-4030 as the input source. Remote Control Operation You can control the T-4030 by using your Onkyo amplifier’s remote controller. With R (Remote Interactive), you can control your R-capable Onkyo CD player, T-4030, and so on with your amp’s remote controller. Onkyo amplifier Connecting the Power Cord Connect the power cord to a suitable wall outlet. Note: • Before connecting the power cord, connect all of other components. Turning On and Standby k ON/STANDBY 1 Press the [k ON/STANDBY] button. The tuner comes on, and the display lights up. To turn the tuner off, press the [k ON/STANDBY] button, or press the remote controller’s [k ] button. The tuner will enter Standby mode. R jack Onkyo CD player R jack T-4030 Notes: • Push each plug in all the way to make a good connection. • Connecting them to another manufacturer’s component may cause a malfunction. See the manuals supplied with your other Onkyo components for more information. En-13 Listening to the Radio Listening to FM Stations With the built-in tuner, you can enjoy FM radio stations. BAND Manual Tuning To activate this mode, press the [TUNING MODE] button to turn off the “AUTO” indicator. In this mode, you will receive the broadcast in monaural sound. 3 Press the TUNING [a] or [s] button. You can also use the remote controller’s arrow [D]/[F] buttons to tune the radio. Manual Tuning The frequency stops changing when you release the button. Press the buttons repeatedly to change the frequency one step at a time. TUNING MODE TUNING MODE BAND The frequency changes in 0. 05 MHz steps for FM. When tuned to a stereo FM station, the FM ST indicator also appears. / FM ST 1 Use the tuner’s [BAND] button, or the remote controller’s [BAND] button to select FM. Tuning to Weak FM Stereo Stations If the signal from a stereo FM station is weak, it may be impossible to get good reception. In this case, switch to Manual Tuning mode and listen to the station in mono. Band Frequency (Actual display depends on the country. ) 2 Press the [TUNING MODE] button or the remote controller’s [MODE] button so that the AUTO indicator appears or disappears from the display. AUTO indicator Auto Tuning To activate this mode, press the [TUNING MODE] button to turn on the “AUTO” indicator. In this mode, you will receive the broadcast in stereo sound. En-14 Listening to the Radio—Continued ■ Tuning into Stations by Frequency You can tune to FM stations directly by entering the appropriate frequency. Presetting FM Stations PRESET AUTO SCAN Number buttons MEMORY TUNING MODE TUNING D. TUN &, (, #, 5, ENTER 1 Press the remote controller’s [D. TUN] button. SETUP Number buttons (Actual display depends on the country. ) 2 Within 8 seconds, use the number buttons to enter the frequency of the radio station. Presetting FM stations is performed by the tuner. 1 2 Tune to the FM station that you want to store as a preset. The preset number flashes. (Actual display depends on the country. ) 3 4 While the preset number flashes (about 8 seconds), use the PRESET [a]/[s] buttons to select a preset from 1 through 40. The station or channel is stored and the preset number stops flashing. Repeat this procedure for all of your favorite FM radio stations. En-15 Listening to the Radio—Continued ■ Selecting Presets To select a preset, use the number buttons on the remote controller, the remote controller’s arrow [A]/[S] buttons or the tuner’s PRESET [a]/[s] buttons. 4 When you’ve finished editing the name and want to store it, be sure to use the arrow [D]/[F]/[A]/[S] button to select “OK” and then press [ENTER]. If you fail to do this, the name won’t be saved. ■ Deleting Presets 1 2 Select the preset that you want to delete. [. . . ] The default setting is “Strong”. SETUP &, (, #, 5, ENTER &, (, #, 5, ENTER RETURN SETUP RETURN 1 2 3 Turn on the power. Use the arrow [D]/[F] buttons to select “ASb, ” and then press [ENTER]. The Hardware setup menu appears in the display. 1 2 3 Press the [SETUP] button on the remote controller. Use the Arrow [D]/[F] buttons to select “Search Level”, and then press [ENTER]. [. . . ]