User manual ONKYO T-4037 service manual

[. . . ] REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Important Safeguards 1. Read Instructions ­ All the safety and operating instructions should be read before the appliance is operated. Retain Instructions ­ The safety and operating instructions should be retained for future reference. [. . . ] (3. 5mm) diameter miniature twoconductor phone plug is included with this unit and with every compact disc player and cassette deck that bears the mark. T-4037 REMOTE CONTROL Operation Supplied cable Amplifier Other Information cable Stereo cassette deck cable CD player 9 Antenna connections Connecting the FM antenna Connecting the antenna cable 1. Close the lever. FM indoor antenna The supplied FM antenna is for indoor use only. Move the antenna in various directions until the clearest signal is received. Fix it with push pins or similar implements in the position that will cause the least amount of distortion. U. S. and Canadian models Other models 300 75 FM AM ANTENNA ANTENNA FM 75 FM outdoor antenna If the reception is not very clear with the supplied FM antenna, the use of an outdoor antenna is recommended. Please make sure that you follow the considerations below regarding the location. · Keep the antenna away from noise sources (neon signs, busy roads etc. ). · To avoid the risk of lightning and electrical shock, grounding is necessary. Follow item 19 of the "Important Safeguards" on page 3 when you install the outdoor antenna. U. S. and Canadian models Other models 75 ohms coaxial cable 300 75 FM AM 10 ANTENNA ANTENNA FM 75 Connecting the AM antenna (U. S. and Canadian models only) · AM reception is available only on the U. S. The received time information (the day of the week and the time) appears. 12 · You may wish to adjust the clock manually because the time information may differ depending on the RDS station detected. If so, follow the manual clock adjustment procedure described on page 14. · There may be cases in which you can listen to r a d i o b ro a d c a s t s b u t c a n n o t u s e t h e ACCUCLOCK function. · Once activated, ACCUCLOCK will remember the RDS station it uses for several weeks even if the power cord of the tuner is unplugged. If you move outside the service area of the memorized RDS station and find out that ACCUCLOCK is not functioning, see "Confirming/changing the RDS Station used by ACCUCLOCK" on page 13 to change the memorized RDS station. POWER INPUT SELECTOR MEMORY TIMER PRESET® FM STEREO TUNER PRESET TIMER MEMORY CLEAR G. EQUALIZER ACOUSTIC MODE CLOCK CALL SLEEP PRESENCE EFFECT TUNER PRESET TAPE FM AM DVD PAUSE/STEP REPEAT SCROLL MD PLAY MODE CLEAR REC AUTO / MONO STANDBY/ ON REPEAT RANDOM CD TUNING MEMORY CLEAR DISC DISPLAY CHARACTER ACCUCLOCK T-4037 TIMER UP/DOWN ENTER TIMER 1 CD/MD 2 3 4 5 6 UP/DOWN 7 8 9 VOLUME ENTER --/--- 10/0 MUTING REMOTE CONTROLLER RC-398S The remote controller comes with the Onkyo A-905X amplifier. Before Using The following procedures are based on the front panel of the T-4037. However, you can also perform the procedure using the remote controller that comes with Onkyo A-905X amplifier. On the remote controller, press the "ENTER" button and "UP/DOWN" button instead of the "MEMORY" button and PRESET/® button respectively. 2 If "AUTO" appears on the display, press the MEMORY button. If "MANUAL" appears on the display, press the PRESET or ® button to select "AUTO, " then press the MEMORY button. MEMORY Connections Confirming/changing the RDS station used by ACCUCLOCK If you wish to know which RDS station has been used to set the clock by ACCUCLOCK, or to use a different RDS station signal to set the clock, follow the steps below: MHz 1 Press the TIMER button repeatedly until "ADJUST" is selected on the display, then press the MEMORY button. TIMER The example shown above indicates that the ACCUCLOCK function uses the RDS station whose information appears on the display (FM 88. 10 MHz). If RDS station signals cannot be received successfully, "- -. --" will appear instead of the radio frequency of the station. If you wish to change the selected RDS station or if no RDS station is selected, choose the desired RDS station by using the PRESET or ® button, then press the MEMORY button. Operation Other Information MEMORY "AUTO" or "MANUAL" appears on the display. 13 Setting the Clock POWER INPUT SELECTOR MEMORY TIMER PRESET® FM STEREO TUNER PRESET TIMER MEMORY CLEAR G. EQUALIZER ACOUSTIC MODE CLOCK CALL SLEEP PRESENCE EFFECT TUNER PRESET TAPE FM AM DVD PAUSE/STEP REPEAT SCROLL MD PLAY MODE CLEAR REC AUTO / MONO STANDBY/ ON REPEAT RANDOM CD TUNING MEMORY CLEAR DISC DISPLAY CHARACTER ACCUCLOCK T-4037 TIMER UP/DOWN ENTER TIMER 1 CD/MD 2 3 4 5 6 UP/DOWN 7 8 9 VOLUME ENTER --/--- 10/0 MUTING REMOTE CONTROLLER RC-398S The remote controller comes with the Onkyo A-905X amplifier. Setting the clock manually The following procedures are based on the front panel of the T-4037. However, you can also perform the procedure using the remote controller that comes with Onkyo A-905X amplifier. [. . . ] (See the figure below. ) · If you press the SLEEP button during timer play or timer recording, the power will be switched off at the SLEEP timer's OFF time. · If more than two timer mode settings are made at the same time, the "WEEKDAY" setting has the priority over the "WEEKEND" setting. · The timer recording setting will be cancelled if the recording does not start at the ON time (for example, if the power is already on). activate not activate activate Connections 1 Start playing something you would like to listen to. (CD, tape, MD or radio broadcast). 2 Press the SLEEP button repeatedly to set the desired sleep time. SLEEP Operation TIMER AUTO MIN STEREO SLEEP WEEKDAY The time value will decrease from 90 minutes to 10 minutes in steps of 10 minutes. After a specified period of time, the power will be switched off automatically. [. . . ]