User manual ONKYO T-4055 service manual

[. . . ] REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Important Safeguards 1. Read Instructions ­ All the safety and operating instructions should be read before the appliance is operated. Retain Instructions ­ The safety and operating instructions should be retained for future reference. [. . . ] · Keep the antenna away from noise sources (neon signs, busy roads etc. ). · To avoid the risk of lightning and electrical shock, grounding is necessary. Follow item 19 of the "Important Safeguards" on page 3 when you install the outdoor antenna. U. S. and Canadian models Other models 75 ohms coaxial cable 300 75 FM AM 10 ANTENNA ANTENNA FM 75 Connecting the AM antenna (U. S. and Canadian models only) · AM reception is available only on the U. S. Assembling the AM loop antenna Assemble the loop antenna as shown in the illustration. Before Using Insert into the hole. Connecting the antenna cable 1. Close the lever. Connections Connecting the AM loop antenna The AM loop antenna is for indoor use only. Set it in the direction and position where you receive the clearest sound. Put it as far as possible away from this unit, TV, speaker cables, and power cords. Operation 300 75 FM AM ANTENNA Connecting an AM outdoor antenna When reception is not satisfactory with the supplied AM loop antenna alone, connection of an outdoor antenna is recommended. The outdoor antenna will be more effective if it is stretched horizontally above a window or outside. · To avoid the risk of lightning and electrical shock, grounding is necessary. On the remote controller, press the "ENTER" button and "UP/DOWN" button instead of the "MEMORY" button and PRESET/® button respectively. 2 If "AUTO" appears on the display, press the MEMORY button. If "MANUAL" appears on the display, press the PRESET or ® button to select "AUTO, " then press the MEMORY button. MEMORY Connections Confirming/changing the RDS station used by ACCUCLOCK If you wish to know which RDS station has been used to set the clock by ACCUCLOCK, or to use a different RDS station signal to set the clock, follow the steps below: MHz 1 Press the TIMER button repeatedly until "ADJUST" is selected on the display, then press the MEMORY button. TIMER The example shown above indicates that the ACCUCLOCK function uses the RDS station whose information appears on the display (FM 88. 10 MHz). If RDS station signals cannot be received successfully, "- -. - -" will appear instead of the radio frequency of the station. If you wish to change the selected RDS station or if no RDS station is selected, choose the desired RDS station by using the PRESET or ® button, then press the MEMORY button. Operation Other Information MEMORY "AUTO" or "MANUAL" appears on the display. 13 Setting the Clock STANDBY/ ON MEMORY TIMER PRESET® FM STEREO TUNER PRESET TIMER MEMORY FM MODE CLOCK CLOCK SLEEP GRAPHIC EQ EFFECT MODE PRESET FM TUNER INPUT AM TAPE PAUSE / STEP DVD REPEAT SCROLL MD PLAY MODE CLEAR REC REPEAT RANDOM CD MEMORY CLEAR DISC CLEAR STANDBY/ ON REPEAT PLAY MODE TUNING CDR TONE CLEAR REC DISPLAY CHARACTER ACCUCLOCK T-4055 TIMER UP/DOWN ENTER MUTING TIMER 1 4 2 5 8 3 6 9 ACOUSTIC PRESENCE VOLUME UP/DOWN 7 ENTER --/- - - 10 / 0 The remote controller comes with the Onkyo A-905TX amplifier. Setting the clock manually The following procedures are based on the front panel of the T-4055. However, you can also perform the procedure using the remote controller that comes with Onkyo A-905TX amplifier. On the remote controller, press the "ENTER" button and "UP/DOWN" button instead of the "MEMORY" button and PRESET/® button respectively. 2 Press the PRESET or ® button until the desired day of the week is selected, then press the MEMORY button. PRESET MEMORY 1 Press the TIMER button until "ADJUST" is selected on the display, then press the MEMORY button. If you do not operate any button for about eight seconds after you press the TIMER button, the system displays the previous indication. TIMER The time will flash on the display. The number buttons on the remote controller: SUN: Sunday TUE: Tuesday THU: Thursday SAT: Saturday MON: Monday WED: Wednesday FRI: Friday 3 Use the PRESET or ® button to set the desired time. PRESET MEMORY The day of the week will flash on the display. and non-Canadian models: "AUTO" or "MANUAL" appears on the display. If "MANUAL" appears on the display, press the MEMORY button. If "AUTO" appears on the display, press the PRESET or ® button to select "MANUAL, " then press the MEMORY button. The day of the week will flash on the display. 14 4 Press the MEMORY button. MEMORY Enabling the ACCUCLOCK function If you have set the clock manually (see page 14), the ACCUCLOCK function is automatically disabled. [. . . ] (See the figure below. ) · If you press the SLEEP button during timer play or timer recording, the power will be switched off at the SLEEP timer's OFF time. · If more than two timer mode settings are made at the same time, the "WEEKDAY" setting has the priority over the "WEEKEND" setting. · The timer recording setting will be cancelled if the recording does not start at the ON time (for example, if the power is already on). activate not activate activate Connections 1 Start playing something you would like to listen to. (CD, tape, MD or radio broadcast). 2 Press the SLEEP button repeatedly to set the desired sleep time. SLEEP Operation TIMER AUTO MIN STEREO SLEEP WEEKDAY The time value will decrease from 90 minutes to 10 minutes in steps of 10 minutes. After a specified period of time, the power will be switched off automatically. [. . . ]