User manual ONKYO T-4087 service manual

[. . . ] Please retain this manual for future reference. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 En WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Important Safety Instructions 1. [. . . ] FM MODE button (18) This button can be used to set the FM mode to stereo or mono. PRESET [+]/[­] buttons (18) When the input source on the A-9355/A-9155 is set to TUNER, these buttons can be used to select presets. TUNING [ ]/[ ] buttons (18) When the input source on the A-9355/A-9155 is set to TUNER, these buttons can be used to tune into stations. * Any remote controller for Onkyo amplifier is available to control T-4087 in a condition of the connection. (On some remote controllers, some buttons shown in the figure are missing. The corresponding functions cannot be controlled by the remote controller. ) 8 Remote Controller--Continued Using the Remote Controller The T-4087 doesn't have its own remote controller, but it can be controlled by using the RC-627S remote controller that's supplied with the Onkyo A-9355/A-9155 Integrated Amplifier. The T-4087 and A-9355/A-9155 must be connected with an cable and an audio cable for this to work. When controlling the T-4087 with the A-9355/A-9155's remote controller, point the controller at the A-9355/A-9155's remote control sensor, as shown. Remote control sensor POWER ON OFF PHONES A SPEAKERS OFF PHONO B OFF CD TUNER BASS TREBLE MD STANDBY ON ON TAPE MUTING PURE DIRECT DOCK LOUDNESS T-4087 A-9355/A-9155 30° 30° 5m RC-627S Notes: · The remote controller may not work reliably if the A-9355/A-9155 is subjected to bright light, such as direct sunlight or inverter-type fluorescent lights. · If another remote controller of the same type is used in the same room, or the A-9355/A-9155 is installed close to equipment that uses infrared rays, the remote controller may not work reliably. · Don't put anything, such as a book, on the remote controller, because the buttons may be pressed inadvertently, thereby draining the batteries. · The remote controller may not work reliably if the A-9355/A-9155 is installed in a rack behind colored glass doors. If circumstances demand it, use a TV/FM antenna splitter, as shown. TV/FM antenna splitter To T-4087 To TV (or VCR) 13 Turning On the T-4087 POWER Listening to the Radio Tuning into Radio Stations Manually TUNING 1 Plug the power cord into a suitable wall outlet (or the AC OUTLET on the A-9355/A-9155's rear panel). To turn off the T-4087, press the [POWER] switch. BAND 2 1 Use the [BAND] button to select FM or AM. The band switches between FM and AM each time you press the button. 2 Using the A-9355/A-9155's Remote Controller ON Use the TUNING [ ]/[ ] buttons to tune into a station. For each button press, the frequency will change in 0. 05 MHz steps for FM, and 9 kHz steps for AM. If you hold down the button for more than 0. 5 second, the T-4087 will find the next station automatically. RC-627S (remote controller supplied with the A-9355/A-9155) If you're using the T-4087 together with the A-9355/A-9155 Onkyo amplifier, press the remote controller's [ON] button to turn on the T-4087 and A-9355/A-9155. (Plug the T-4087 power cord into the A-9355/A-9155 AC OUTLET. ) Memory backup The T-4087 uses a battery-less memory backup system in order to retain radio presets and other settings when it's unplugged or in the case of a power failure. Backup data can be stored incorrectly or destructed, and lead to a malfunction if either of the following operations is performed: · turning off the power immediately after an operation. When a malfunction occurred due to those operations, initialize T-4087 to its factory defaults. To initialize T-4087, press the [DISPLAY] button while holding down the [FM MODE] button. When the power is turned off while the Auto Preset is running, T-4087 is initialized to its factory defaults. 14 Listening to the Radio--Continued You can store up to 30 of your favorite radio stations as presets for quick selection. Stations can be preset automatically using the Auto Preset function or manually. [. . . ] Setting FM mode This button can be used to set the FM mode to stereo or mono. Note: If the current preset doesn't have a name, no text will be displayed. Tuning Manually Press the Down [ ] button to decrease the tuning frequency. Note: If you're using another Onkyo amplifier's remote controller, refer to its instruction manual for operating information. 18 Listening to the Radio--Continued Using RDS (European models only) RDS stands for Radio Data System and is a method of transmitting data in FM radio signals. The T-4087 supports the following types of RDS data: PS: Program Service Name When tuned to an RDS station that's broadcasting PS information, the station's name appears on the display. RT: Radio Text When tuned to an RDS station that's broadcasting RT text information, the text scrolls across the display. [. . . ]