Detailed instructions for use are in the User's Guide.
[. . . ] Contents
AM/FM Tuner
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
T-4355
Instruction Manual
Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new Tuner. [. . . ] The T-4355 and A-9355/A-9155 must be connected with an cable and an audio cable for this to work. When controlling the T-4355 with the A-9355/A-9155's remote controller, point the controller at the A-9355/A-9155's remote control sensor, as shown.
Remote control sensor
POWER
ON OFF
PHONES
A SPEAKERS
OFF
PHONO B
OFF
CD TUNER
BASS TREBLE MD
STANDBY
ON ON
TAPE MUTING PURE DIRECT DOCK
LOUDNESS
T-4355
A-9355/A-9155
30°
30°
5m
RC-627S
Notes: · The remote controller may not work reliably if the A-9355/A-9155 is subjected to bright light, such as direct sunlight or inverter-type fluorescent lights. · If another remote controller of the same type is used in the same room, or the A-9355/A-9155 is installed close to equipment that uses infrared rays, the remote controller may not work reliably. · Don't put anything, such as a book, on the remote controller, because the buttons may be pressed inadvertently, thereby draining the batteries. · The remote controller may not work reliably if the A-9355/A-9155 is installed in a rack behind colored glass doors. · The remote controller will not work if there's an obstacle between it and the A-9355/A-9155's remote control sensor.
9
Connecting the T-4355
Before Making Any Connections
· Refer to the instructions that came with the component you are connecting. · Do not plug in the power cord until all other connections are complete. · Do not bind audio cables with power cords and speaker cables. · To prevent interference, keep power cords and speaker cables as far away as possible from the tuner's antennas.
RCA Audio Connection Color Coding
· Red connectors are used for the right channel, and white connectors are used for the left channel.
Left (white) L
Right (red)
R
· Push each plug in all the way to make a good connection (loose connections can cause noise or malfunctions).
Right!
Wrong!
Connecting an amplifier
Use the supplied audio cable to connect the T-4355's ANALOG AUDIO OUTPUT L/R jacks to the analog input jacks on the amplifier, as shown. To use the system functions, use the supplied cable to make an connection.
T-4355
Supplied audio cable
L
Supplied
cable
CD PHONO TUNER
MD
TAPE
DOCK POWER BASS A SPEAKERS B PHONES PURE DIRECT
OFF OFF
TREBLE LOUDNESS
R TUNER
ON
OFF
MUTING
ON
ON
STANDBY
Amplifier
Notes: · The T-4355 has two jacks. · To use , you must make an audio connection between the T-4355 and the other component. · If the T-4355 is used with another Onkyo component, such as the A-9355/A-9155, refer to its instruction manual as well.
10
Connecting the T-4355--Continued
About the System Functions
If you connect the T-4355 to another Onkyo -capable component with the supplied cable and audio cable, you can use the following system functions. Direct Change When you select a radio preset or change the band (AM, FM), your Onkyo amplifier will automatically select the T-4355 as the input source. Remote Control Operation You can control the T-4355 by using your Onkyo amplifier's remote controller. With (Remote Interactive), you can control your -capable Onkyo CD player, T-4355, and so on with your amplifier's remote controller. · To use , you must make an analog audio connection between your amplifier and each audio component.
Onkyo amplifier (A-9355), etc.
Notes: · Push each plug in all the way to make a good connection. Connecting them to another manufacturer's component may cause a malfunction. See the manuals supplied with your other Onkyo components for more information.
jack Onkyo CD player (DX-7355), etc.
jack T-4355
jack
Remote Interactive Dock, etc.
cable
11
Connecting Antennas
This section explains how to connect the supplied indoor FM antenna and AM loop antenna and how to connect commercially available outdoor FM and AM antennas.
AM antenna push terminals FM antenna jack
Connecting the AM Loop Antenna
The supplied indoor AM loop antenna is for indoor use only.
1
Assemble the AM loop antenna, inserting the tabs into the base, as shown.
2
Connecting the Indoor FM Antenna
The supplied indoor FM antenna is for indoor use only.
1
Attach the FM antenna, as shown.
Connect both wires of the AM loop antenna to the AM push terminals, as shown. Make sure that the wires are attached securely and that the push terminals are gripping the bare wires, not the insulation.
Insert the plug fully into the jack.
Once your T-4355 is ready for use, you'll need to tune into an FM radio station and adjust the position of the FM antenna to achieve the best possible reception.
Push
Insert wire
Release
2
Use thumbtacks or something similar to fix the FM antenna into position.
Black
Thumbtacks, etc.
Once your T-4355 is ready for use, you'll need to tune into an AM radio station and adjust the position of the AM antenna to achieve the best possible reception. Keep the antenna as far away as possible from your T-4355, TV, speaker cables, and power cords. If you cannot achieve good reception with the supplied indoor AM loop antenna, try using it with a commercially available outdoor AM antenna.
Caution: Be careful that you don't injure yourself when using thumbtacks. If you cannot achieve good reception with the supplied indoor FM antenna, try using a commercially available outdoor FM antenna instead.
12
Connecting Antennas--Continued
Connecting an Outdoor FM Antenna
If you cannot achieve good reception with the supplied indoor FM antenna, try using a commercially available outdoor FM antenna instead.
Connecting an Outdoor AM Antenna
If good reception cannot be achieved using the supplied AM loop antenna, an outdoor AM antenna can be used in addition to the loop antenna, as shown.
Outdoor antenna Insulated antenna cable AM loop antenna White
Antenna adapter (not included)
Notes: · Outdoor FM antennas work best outside, but acceptable results can sometimes be obtained when installed in an attic or loft. [. . . ] Note: If the signal from an RDS station is weak, RDS data maybe displayed intermittently or not at all.
Displaying RDS information
Note: You must be tuned to an FM station that supports RT (Radio Text) in order to display any text.
DISPLAY
Press the [DISPLAY] button repeatedly to show the following information.
Frequency Preset name or PS (Program Service name) RT (Radio Text)
Notes: · If the current station does not support RDS, only the frequency and preset name (see page 17) will be displayed. If the current preset has no name, only the frequency will be displayed. · In some cases, it may take between 2 and 15 seconds for the RT text to be displayed. · The message "Waiting···" may appear while the RT data is being received. [. . . ]