User manual ONKYO TA-RW99 service manual

[. . . ] REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Important Safety Instructions 1. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. [. . . ] This setting is effective with Dolby Digital, Dolby Digital Plus and Dolby TrueHD only. Note · If the "Surround Back" setting is set to "None" ( page 46), this setting cannot be selected. · If the "Front High" setting is enabled ( page 46), this setting is fixed at "Manual". Dolby PL IIx Music (2ch Input) These settings apply to only 2-channel stereo sources. If you're not using any surround back speakers, these settings apply to Dolby Pro Logic II, not Dolby Pro Logic IIx. Panorama On Off With this setting, you can broaden the width of the front stereo image when using the Dolby Pro Logic IIx Music listening mode. En 49 DTS Neo:6 Music Center Image 0 to 2 to 5 The DTS Neo:6 Music listening mode creates 6-channel surround sound from 2-channel stereo sources. With this setting, you can specify by how much the front left and right channel output is attenuated in order to create the center channel. Changing the value from "0" to "5" will spread the sound of the center channel to left and right (outwards). Source Setup Items can be set individually for each input selector. Preparation Press the input selector buttons to select an input source. Main menu Source Setup Audyssey The tone for each speaker is set automatically by Audyssey 2EQ® Room Correction and Speaker Setup. To enable the following settings, you must first perform the Room Correction and Speaker Setup ( page 31). The Audyssey indicator lights. Note · If the "Audyssey" setting is set to "Off", the "Equalizer" settings are applied ( page 48). · When "Audyssey Quick Start" has been used for measurement, the "Audyssey"setting cannot be selected. · These technologies cannot be used when: ­ a pair of headphones is connected, or ­ either Pure Audio (European, Australian and Asian models) or Direct listening mode is selected. Audyssey DSXTM Soundstage ­3dB to Reference to +3dB With this setting, you can adjust the sound stage when using Audyssey DSX. Note · This listening mode can be selected only when all the following conditions are satisfied: ­ The center speaker is connected. However, if Audyssey 2EQ is on, the two technologies work in tandem to provide well-balanced sound for every listener at any volume level. About Audyssey Dynamic Volume® Audyssey Dynamic Volume solves the problem of large variations in volume level between television programs, commercials, and between the soft and loud passages of movies. Dynamic Volume looks at the preferred volume setting by the user and then monitors how the volume of program material is being perceived by listeners in real time to decide whether an adjustment is needed. Whenever necessary, Dynamic Volume makes the necessary rapid or gradual adjustments to maintain the desired playback volume level while optimizing the dynamic range. Audyssey Dynamic Volume works fine by itself, but can also be used with Audyssey Dynamic EQ. When both are on, Audyssey Dynamic EQ adjusts the perceived bass response, tonal balance, surround impression, and dialog clarity whether watching movies, flipping between television channels, or changing from stereo to surround sound content, when Dynamic Volume adjusts the volume. Dynamic Volume Off Light: Activates Light Compression Mode. It quiets the loud parts, such as explosions, and boosts the quiet parts so they can be heard. En 51 IntelliVolume IntelliVolume ­12dB to 0dB to +12dB in 1 dB steps. With IntelliVolume, you can set the input level for each input selector individually. This is useful if one of your source components is louder or quieter than the others. If a component is noticeably louder than the others, use to reduce its input level. If it's noticeably quieter, use to increase its input level. Note · IntelliVolume does not work for Zone 2. Name input area 4 - 4. [. . . ] · Operation of the player/recorder is possible using the remote controller supplied with the AV receiver. * The following components are of January 2011). TV · Toshiba REGZA-LINK compatible TV · Sharp TV Players/Recorders · Onkyo and Integra -compatible players · Toshiba REGZA-LINK compatible players and recorders (only when used together with Toshiba REGZA-LINK compatible TV) · Sharp players and recorders (only when used together with Sharp TV) * Models other than those mentioned above may have some interoperability if compatible with CEC, which is part of the HDMI Standard, but operation cannot be guaranteed. Note · For proper linked operations, do not connect more compatible components than the quantities specified below, to the HDMI input terminal. ­ Blu-ray Disc/DVD recorders/Digital Video Recorders: up to three. · Do not connect the AV receiver to the other AV receiver/AV amplifier via HDMI. · Proper linked operations are not guaranteed when more -compatible components than the above-mentioned quantities are connected. Depending on the model used, not all operations may be available. En 84 How to connect and setup 3 1 Confirm the connecting and setting. [. . . ]