User manual ONKYO TX-26

[. . . ] REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Important Safeguards 1. Read Instructions ­ All the safety and operating instructions should be read before the appliance is operated. Retain Instructions ­ The safety and operating instructions should be retained for future reference. [. . . ] · You may not be able to play some DTS source signals from certain CD players and LD players even if you connect the player to the TX-26 digitally. This is because the digital signal has been processed (such as the output level, sampling frequency, or frequency response) and the TX-26 cannot recognize the signal as DTS data. Therefore you may hear noise when you play a DTS source while processing the signal. · The outputs for the VIDEO 1 OUT, VIDEO 2 OUT, TAPE OUT, and ZONE 2 OUT output analog audio signals. · If a compact disc or LD encoded in the DTS format is played back with "PCM" selected, only noise will be produced. Always select "All" or "DTS" when playing back DTS-encoded sources. 2-2. Multichannel Setup sub-menu This setting is normally set to "No, " and only needs to be changed to "Yes" if a DVD player, MPEG decoder, or other component that has a multi channel port is connected to the MULTI CHANNEL INPUT port for 5. 1-channel, 6. 1-channel, or 7. 1-channel audio. For example, if a DVD player is connected to the MULTI CHANNEL INPUT port, then select DVD at the front panel as the input source, bring up this sub-menu, and select "Yes" for the Multichannel setting. You can only select Multichannel with the AUDIO SELECTOR button when "Yes" is selected here. Advanced Menu 2. Input Setup Input:DVD 2-2. Multichannel Setup Input:DVD a. Multichannel :Yes Quit:|SETUP| Input source selected CD PHONO FM AM TAPE DVD VIDEO 1 VIDEO 2 VIDEO 3 VIDEO 4 VIDEO 5 Multichannel No No No No No Yes No No No No No Note: When playing a device that is actually connected to the MULTI CHANNEL INPUT terminal, select Multichannel with the AUDIO SELECTOR button. 34 Input Setup 2-3. Video Setup sub-menu Advanced Menu 2. Input Setup Input:DVD 2-3. Video Setup Input:DVD a. Video :DVD b. Component Video :INPUT1 b. Component Video If a component is connected to the one of the COMPONENT VIDEO inputs (1 or 2), then that input must be set here. This Intelli Volume setting allows you to preset a volume level for each input source separately so that when you do switch from one input source to another, the TX-26 adjusts the volume accordingly so that the resulting volume stays the same. To set the Intelli Volume, simply select an input source at the front panel, and if that source is quieter than other sources, increase its decibel level with the cursor button, or if it is louder than other sources, decrease its decibel level with the cursor button. The Intelli Volume can be adjusted between ­12 and +12 decibels. Advanced Menu 2. Input Setup Input:DVD 2-4. Character Input Input:DVD b. Character : ABCDEFGHIJKLM NOPQRSTUVWXYZ abcdefghijklm nopqrstuvwxyz |ENTER| 0123456789-. ' Back: ()+*/=, :;!?_ |RETURN| 36 Input Setup 2-6. Listening Mode Preset sub-menu With the TX-26, you can set a different listening mode for each different signal type that comes from each input source. For example, if your DVD player also plays compact discs and the DVD video signal is Dolby Digital and the compact disc signal is PCM, then you can set a different listening mode for each. This is especially convenient if you frequently play the same types of movies or music. * The 5. 1-channel digital surround format has a variety of versions including Dolby Digital and DTS. The 5. 1- channel digital surround format enables you to individually record and play five full-range (20 Hz to 20 kHz) channels (left and right front, center, and two surround channels) plus an LFE channel (Low Frequency Effect) for the low-range effect sound. It will create a realistic sound that can be heard in the theaters and concert halls. Advanced Menu 2. Input Setup Input:DVD 2-6. ListeningMode Preset Input:DVD a. Analog/PCM :Stereo b. PCM fs=96k :Stereo c. Dolby D :Dolby D d. DTS :DTS f. D. F. 2ch :PLII g. D. F. Mono:Mono Quit:|SETUP| Relationship between input source and listening mode Input source signal (display) Type of software Analog/PCM (2ch) Tape, CD, MD, Record, Tuner, DVD (Stereo), LD, Digital satellite o o o o o o o o o o PCM fs=96kHz DVD (96k/24bit) Dolby D (Multi CH) DVD DTS (Multi CH) DVD DTS-CD D. F. 2ch (Digital Audio Format) DVD Digital satellite D. F. Mono DVD Listening Mode Direct Stereo Mono Theater-Dimensional Dolby Pro Logic II Dolby Digital DTS Neo:6 DTS DTS-ES Discrete DTS-ES Matrix THX Cinema(PLII) THX Cinema(Neo:6) THX Surround EX DTS-ES THX Cinema Mono Movie Enhanced 7 Orchestra Unplugged Studio-Mix TV Logic All Ch Stereo o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o The listening modes that can be set are different for each input source format. Note: You may not be able to select all the listening modes shown here depending on your speaker configuration or the selected input source. 37 Input Setup Input source signals a. Analog/PCM Analog sources consist of LP records, FM and AM broadcasts, cassette tapes, and the such. [. . . ] © Check the Video Setup submenu of the Input Setup menu (page 35). · To listen to multichannel audio, "Yes" must be selected in the "Multichannel" in the Multichannel setup sub-menu of the Input Setup menu. Also, it is necessary to select Multichannel with the AUDIO SELECTOR button. © Check that the component is connected to the MULTI CHANNEL INPUT port and check the Setup menu settings. [. . . ]