User manual ONKYO TX-8011

[. . . ] 2 Stereo Receiver TX-8011 Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Instruction Manual Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new Stereo Receiver. [. . . ] J AC OUTLET (15) This switched AC outlet can be used to supply power to another component. B C D E F 8 Remote Controller 1 2 3 4 5 POWER SLEEP 6 TAPE-1 INPUT SELECTOR TUNER PHONO CD TAPE-2 DECK-A DECK-B GROUP TUNER PRESET MUTING 7 8 CD DISC VOLUME REMOTE CONTROLLER RC-330S A POWER button (16) This button is used to set the TX-8011 to On or standby. B INPUT SELECTOR buttons (17, 19) These buttons are used to select the input sources. C DECK-A & DECK-B (works only with Onkyo cassette recorder connected via . For singlecassette recorder, use the DECK-B buttons) Play [ ] button This button is used to start tape playback. Reverse Play [ ] button This button is used to start reverse playback. Rec/Pause [ ]/[ ] button This button is used to start and pause tape recording. Rewind/FF [ ]/[ ] buttons The Rewind [ ] button is used to start rewind. D TUNER (19, 20) GROUP button This button is used to select the radio preset groups. PRESET [ ]/[ ] buttons These buttons are used to select the radio presets. E CD (works only with Onkyo CD players connected via ) Pause [ ] button This button is used to pause CD playback. Previous & Next [ ]/[ ] buttons The Previous [ ] button is used to select the previous track. During playback, the first press selects the beginning of the current track. H VOLUME [ ]/[ ] buttons (17) These buttons are used to set the volume of the TX-8011. 9 Remote Controller--Continued Installing the Batteries Using the Remote Controller To use the remote controller, point it at the TX-8011's remote control sensor, as shown below. Remote control sensor 1 Open the battery compartment, as shown. 2 Insert the two supplied batteries (AA/R6) in accordance with the polarity diagram inside the battery compartment. 30° 30° f 16 x. pro m) Ap (5 t. 3 Close the battery compartment. Notes: · The batteries should last for about six months, although this will vary with usage. · If the remote controller doesn't work reliably, try replacing the batteries. · Don't mix new and old batteries or different types of batteries. · If you intend not to use the remote controller for a long time, remove the batteries to prevent damage from leakage or corrosion. · Expired batteries should be removed as soon as possible to prevent damage from leakage or corrosion. Notes: · The remote controller may not work reliably if the TX-8011 is subjected to bright light, such as direct sunlight or inverter-type fluorescent lights. · If another remote controller of the same type is used in the same room, or the TX-8011 is installed close to equipment that uses infrared rays, the remote controller may not work reliably. · Don't put anything, such as a book, on the remote controller, because the buttons may be pressed inadvertently, thereby draining the batteries. · The remote controller may not work reliably if the TX-8011 is installed in a rack behind colored glass doors. · The remote controller will not work if there's an obstacle between it and the TX-8011's remote control sensor. 10 Connections Connecting Speakers Before you connect your speakers, read the following: · Disconnect the power cord from the wall outlet. In other words, connect positive (+) terminals only to positive (+) terminals, and negative (­) terminals only to negative (­) terminals. [. . . ] · Make sure that the inputs and outputs of all components are properly connected (page 11­15). · Make sure that the polarity of the speaker cables is correct and that the bare wires are in contact with metal part of each speaker terminal (page 11) · Make sure that the input source is properly selected (page 17). · If the AUDIO MUTE indicator is shown on the display, press the remote controller's [MUTING] button to unmute the TX-8011 (page 17). · If your turntable has a moving coil (MC) type cartridge, you'll need a commercially available MC head amp (page 14). [. . . ]