User manual ONKYO TX-82

[. . . ] Please retain this manual for future reference. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 En WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Important Safeguards 1. [. . . ] Message area This area of the display shows various information about the currently selected source. H B I C J K D E F 7 Front & Rear Panels--Continued Rear Panel 1 2 3 4 5 6 AM REMOTE CONTROL ANTENNA GND FM 75 SPEAKERS R IN IN OUT L AC OUTLET IN OUT IN A L L B R R A AC 120V 60Hz SWITCHED 120W 1A MAX. B PHONO CD TAPE 1 TAPE 2 78 9 J A Grounding screw (14) This screw is for connecting a turntable's ground wire. AM ANTENNA (12, 13) These push terminals are for connecting an AM antenna. SPEAKERS A (11) These lever terminals are for connecting speaker set A. SPEAKERS B (11) These lever terminals are for connecting speaker set B. (15) These (Remote Interactive) jacks can be connected to the jacks on other Onkyo CD player and cassette recorder. The TX-82's remote controller can then be used to control those components. Note: To use , you must make an analog audio connection between the TX-82 and the other component. can only be used with Onkyo components. G PHONO IN (14) These jacks can be used to connect a turntable with a moving-magnet cartridge. H CD IN (14) These jacks can be used to connect a CD player with an analog output. I TAPE 1, 2 IN/OUT (14) This analog audio input and output can be used to connect a cassette recorder, CD recorder, or other recorder with an analog input and output. J AC OUTLET (15) This switched AC outlet can be used to supply power to another component. B C D E F 8 Remote Controller 1 2 3 4 5 POWER SLEEP 6 TAPE-1 INPUT SELECTOR TUNER PHONO CD TAPE-2 DECK-A DECK-B GROUP TUNER PRESET MUTING 7 8 CD DISC VOLUME REMOTE CONTROLLER RC-330S A POWER button (16) This button is used to set the TX-82 to On or standby. · The impedance of each speaker connected to this unit must be no lower than 4 ohms. If you're using only speakers A or speakers B, the minimum speaker impedance is 4 ohms. If you're using both speakers A and speaker B, the minimum speaker impedance is 8 ohms. If you use speakers with a lower impedance, and use the amplifier at high volume levels for a long period of time, the built-in protection circuit may be activated. · Unnecessarily long or very thin speaker cables may affect the sound quality and should be avoided. · Don't connect more than one cable to each speaker terminal. Doing so may damage the TX-82. A B · If you want to connect a single speaker instead of a pair, connect it to either the left or right speaker terminals, not both. NO! R L A A NO! R L A A 1 Strip 3/8" (10 mm) of insulation from the ends of the speaker cables, and twist the bare wires tightly. Push the lever to open the hole, insert the bare wire into the hole, and then push the lever again to close the hole, thereby securing the wire. 3/8" (10 mm) 2 Maker sure that the speaker connectors are gripping the bare wires, not the insulation. The following illustration shows which speakers should be connected to which terminals. Speaker set A Right speaker Left speaker SPEAKERS R L AM REMOTE CONTROL A A ANTENNA GND FM 75 SPEAKERS R IN IN OUT L AC OUTLET B B IN OUT IN A L B A L AC 120V 60Hz SWITCHED 120W 1A MAX. B R R PHONO CD TAPE 1 TAPE 2 CAUTION: SPEAKER IMPEDANCE A or B: 4 ohms min. /speaker A + B: 8 ohms min. /speaker Right speaker Left speaker Speaker set B 11 Connections--Continued Connecting the Supplied FM & AM Indoor Antennas ANTENNA AM REMOTE CONTROL ANTENNA GND FM 75 SPEAKERS R IN IN OUT L AC OUTLET IN OUT IN A L L B R R A AC 120V 60Hz SWITCHED 120W 1A MAX. B PHONO CD TAPE 1 TAPE 2 Adjusting the Position of the FM Indoor Antenna The FM indoor antenna is for indoor use only. Extend the antenna fully and point it in various directions to find the best reception. If the reception is not very good with the supplied FM indoor antenna, use an outdoor antenna. 1 Strip the insulation from the end of the wire. 2 Fully insert the bare wire. GND FM 75 AM ANTENNA Adjusting the Position of the AM Indoor Antenna The AM loop antenna is for indoor use only. [. . . ] · Make sure that the power cord is properly plugged into the wall outlet. · Unplug the power cord from the wall outlet, wait five seconds or more, then plug the cable in again. Remove the power cord from the wall outlet immediately and contact your Onkyo dealer. Audio There's no sound, or it's very quiet?· Make sure that all audio connecting plugs are pushed in all the way (pages 11­15). [. . . ]