User manual ONKYO TX-8222

[. . . ] TX85228222_En. book 1 ÉyÅ[ÉW ÇQÇOÇOÇUîNÇTåéÇSìÅ@ñÿójìÅ@åflëOÇPÇPéûÇTÇPïTM Contents Stereo Receiver Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 TX-8522/ TX-8222 Instruction Manual Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new Stereo Receiver. [. . . ] The video input from the DVD player should be connected to the TV directly. Use an analog audio cable to connect the TX-8222's LINE 1/DVD IN L/R jacks to the analog audio output jacks on the DVD player. / REC (IN) PLAY (OUT) DVD IN V MONITOR OUT Connecting a Remote Interactive Dock (RI Dock) Use an analog audio cable to connect the TX-8522's TAPE 1 IN L/R or VIDEO IN L/R jacks, or to connect the TX-8222's LINE 2 IN L/R or TAPE 1 IN L/R jacks, to the RI Dock's analog audio output jacks. Then use an cable to connect the receiver's jack to the RI Dock's jack, as shown. When you change the input display name to "HDD, " you can operate the RI Dock using the remote controller supplied with the receiver (see page 20). IN V L R DVD L VIDEO IN AUDIO OUT R VIDEO OUT TAPE 1 Remote Interactive Dock R ---- L AUDIO OUT Note: If you use the Onkyo Remote Interactive Dock (DS-A1), flip the RI MODE switch to "HDD" which is located on the underside. 17 TX85228222_En. book 18 y·[W , Q, O, O, U"N, TOEZ, S"ú·@­Ø--j"ú·@OEß`O, P, PZz, T, P·ª Connecting Your Components--Continued Connecting a VCR For the TX-8522, use an analog audio cable to connect the TX-8522's VIDEO IN L/R jacks to the analog audio output jacks on the VCR, and use a video cable to connect the TX-8522's VIDEO IN V jack to the composite video output jack on the VCR. Then use an analog audio cable to connect the TX8522's VIDEO OUT L/R jacks to the analog audio input jacks on the VCR, and use a video cable to connect the TX-8522's VIDEO OUT V jack to the composite video input jack on the VCR. In addition, connect the TX-8522's MONITOR OUT jack to a composite video input jack on the TV. You can select the video and sound from the VCR simultaneously by pressing the VIDEO input selector button. Use an analog audio cable to connect the TX-8222's LINE 1/DVD IN L/R or LINE 2 IN L/R jacks to the analog audio output jacks on the VCR. VIDEO IN V MONITOR OUT IN V L R VIDEO V VIDEO Connecting a TV or Other Component with an Audio Output For the TX-8522, use an analog audio cable to connect the unused audio input L/R jacks on the TX-8522 to the analog audio output jacks on the connected component. For the TX-8222, use an analog audio cable to connect the TX-8222's LINE 1/DVD IN L/R or LINE 2 IN L/R jacks to the analog audio output jacks on the connected component. IN L R L AUDIO OUT R Connecting Components L R VIDEO If you connect other Onkyo components to the receiver with the appropriate and audio cables, you can use the following system functions. cables are special cables solely for use with Onkyo products (no cables are supplied with the receiver). Auto Power On When you turn on the power or start playback on a component that's connected to the receiver, the receiver will turn on automatically. And when you set the receiver to Standby, all connected components will go on Standby as well (the receiver's POWER switch must be set to ON for this to work). Direct Change When playback is started on an audio component connected via , the receiver will automatically select that component as the input source. Remote Control Operation You can control all components in your system by using the receiver's remote controller. See page 10 for more information. L VIDEO IN AUDIO IN R VIDEO IN L AUDIO OUT R VIDEO OUT 18 3_Connection_En 19 y·[W , Q, O, O, U"N, TOEZ, S"ú·@­Ø--j"ú·@OEßOEã, QZz, R, W·ª Connecting Your Components--Continued With (Remote Interactive), you can control your -compatible Onkyo CD player, RI Dock, and so on with the receiver's remote controller. · To use , you must make an analog audio connection between the receiver and each audio component. Receiver Connecting the Power Cords of Other Components The receiver has AC outlets on its rear panel that can be used to connect the power cords of other components that you intend to use with the receiver. These components can then be left turned on so that they turn on and off as and when the receiver is turned on and set to Standby. connector Onkyo CD player, etc. connector Onkyo cassette deck, etc. connector e. g. TX-8522 North American model Remote Interactive Dock, etc. Remote control cable Notes: · Push each plug in all the way to make a good connection. · Use only dedicated cables for connections (no cables are supplied with the receiver). Connecting them to another manufacturer's component may cause the receiver to malfunction. See the manuals supplied with your other Onkyo components for more information. Caution: · Make sure that the total capacity of the components that you connect to the AC OUTLETS does not exceed the stated capacity (e. g. , TOTAL 120 W). Notes: · Onkyo components connected via should be connected directly to a wall outlet, not an AC OUTLETS on the receiver. [. . . ] · Make sure that the polarity of the speaker cables is correct, and that the bare wire is in contact with metal part of each speaker terminal (page 12). · Make sure that the speaker cables are not shorting. 32 TX85228222_En. book 33 ÉyÅ[ÉW ÇQÇOÇOÇUîNÇTåéÇSìÅ@ñÿójìÅ@åflëOÇPÇPéûÇTÇPïTM Troubleshooting--Continued Remote Controller The remote controller doesn't work · Make sure that the batteries are installed with the correct polarity (page 5). Don't mix different types of batteries or old and new batteries (page 5). · Make sure that the remote controller is not too far away from the receiver, and that there's no obstruction between the remote controller and the receiver's remote control sensor (page 10). [. . . ]