User manual ONKYO TX-8410R

[. . . ] 113 En WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Important Safety Instructions 1. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. [. . . ] When tuned into a stereo FM station, the FM STEREO indicator also appears. TUNED AUTO FM STEREO 63 Listening to the Radio--Continued Tuning into Stations by Frequency You can tune into AM and FM stations directly by entering the appropriate frequency. Displaying AM/FM Radio Information DISPLAY MASTER VOLUME STANDBY/ON STANDBY READY ON STANDBY TV INPUT ZONE 2 ZONE 3 Number buttons DVD VCR/DVR CBL/SAT PURE AUDIO AUDIO SEL DVD VCR/DVR CBL/SAT GAME/TV AUX 1 AUX 2 TAPE TUNER CD PHONO DISPLAY 1 GAME/TV 2 AUX1 3 AUX2 + TV CH PUSH TO OPEN 4 TAPE 5 TUNER 6 CD - 7 PHONO 8 0 9 D. TUN TV VOL +10 CLEAR 12 11 --/--- 10 INPUT SELECTOR MACRO D. TUN ZONE3 1 2 3 REMOTE MODE DVD VCR CD CDR/MD TV DIMMER P TO U MEN MEN U ZONE2 Press the [DISPLAY] button to display the available information. RECEIVER DISPLAY CABLE SAT DOCK RECEIVER TAPE/AMP SLEEP 1 RECEIVER Press the [RECEIVER] button, followed by the [D. TUN] button. TUN Listening mode CLEAR (Actual display depends on country. ) Note: · When you select a preset with a custom name (see page 94), its name is displayed instead of the band and frequency. 2 DVD VCR/DVR CBL/SAT 1 GAME/TV 2 AUX1 3 AUX2 4 TAPE 5 TUNER 6 CD Within 8 seconds, use the number buttons to enter the frequency of the radio station. Note: While the [RECEIVER] button is flashing, you cannot select another input source with the remote controller. 7 PHONO 8 0 9 +10 64 Listening to the Radio--Continued Using RDS (not North American model) RDS only works in areas where RDS broadcasts are available. When tuned to an RDS station, the RDS indicator appears. RDS indicator RDS Program Types (PTY) Type None News reports Current affairs Information Sport Education Display NONE NEWS AFFAIRS INFO SPORT EDUCATE DRAMA CULTURE SCIENCE VARIED POP M ROCK M EASY M LIGHT M CLASSICS OTHER M WEATHER FINANCE CHILDREN SOCIAL RELIGION PHONE IN TRAVEL LEISURE JAZZ COUNTRY NATION M OLDIES FOLK M DOCUMENT TEST ALARM What is RDS?RDS stands for Radio Data System and is a method of transmitting data in FM radio signals. It was developed by the European Broadcasting Union (EBU) and is available in most European countries. In addition to displaying text information, RDS can also help you find radio stations by type (e. g. , news, sport, rock, etc. ). The AV receiver supports four types of RDS information: PS (Program Service) Drama Culture Science and technology Varied Pop music Rock music Middle of the road music Light classics Serious classics Other music Weather Finance Children's programmes Social affairs Religion Phone in Travel Leisure Jazz music Country music National music Oldies music Folk music Documentary Alarm test Alarm When tuned to an RDS station that's broadcasting PS information, the station's name will be displayed. Pressing the [DISPLAY] button will display the frequency for 3 seconds. RT (Radio Text) When tuned to an RDS station that's broadcasting text information, the text will be shown on the display (see page 66). PTY (Program Type) This allows you to search RDS radio stations by type (see page 66). TP (Traffic Program) This allows you to search for RDS radio stations that broadcast traffic information (see page 66). Notes: · In some cases, the characters displayed on the AV receiver may not be identical to those broadcast by the radio station. The output is muted and the MUTING indicator flashes on the display. AV receiver DIMMER Press the remote controller's [DIMMER] button repeatedly to select: · Normal + VOLUME light on. You can also use the AV receiver's [DIMMER] button (not European models). MUTING To unmute the AV receiver, press the remote controller's [MUTING] button again, or adjust the volume. Tip: You can specify how much the output is muted with the Muting Level setting (see page 96). 68 Common Functions--Continued Using the Sleep Timer With the sleep timer, you can set the AV receiver so that it turns off automatically after a specified period. SLEEP Displaying Source Information You can display various information about the current input source as follows. Remote controller Press the remote controller's [SLEEP] button repeatedly to select the required sleep time. The SLEEP indicator appears on the display when the sleep timer has been set, as shown. The specified sleep time appears on the display for about 5 seconds, then the previous display reappears. SLEEP indicator DISPLAY Press the [DISPLAY] button repeatedly to cycle through the available information. AV receiver DISPLAY The following information can typically be displayed: Input source Listening mode Signal format* Sampling frequency To cancel the sleep timer, press the [SLEEP] button repeatedly until the SLEEP indicator disappears. Note that if you press the [SLEEP] button while the sleep time is being displayed, you'll shorten the sleep time by 10 minutes. Using Headphones For private listening, you can connect a pair of stereo headphones (1/4-inch phone plug) to the AV receiver's PHONES jack. STANDBY/ON *If the input signal is analog, no format information is displayed. If the input signal is digital but not PCM, the signal format and the number of channels is displayed. For some digital input signals, including multichannel PCM, the signal format, number of channels, and sampling frequency is displayed. Information is displayed for about 3 seconds, then the previous display reappears. STANDBY READY ZONE 2 ZONE 3 PURE AUDIO AUDIO SEL ZONE 2 PHONES POWER OFF ON OFF ZONE 3 Notes: · Always turn down the volume before connecting your headphones. · While the headphones plug is inserted in the PHONES jack, the speakers are turned off and the Headphone indicator lights up. (The Powered Zone 2 speakers are not turned off. ) · When you connect a pair of headphones, the listening mode is set to Stereo, unless it was already set to Pure Audio, Mono, Stereo, or Direct, in which case it stays the same. 69 Common Functions--Continued Selecting Audio Inputs Specifying the Digital Signal Format 1 REC PLAYLIST 2 MASTER VOLUME RANDOM LISTENING MODE STANDBY/ON STEREO REPEAT PURE A SURR AUDIO DIRECT SUBTITLE PLAY MODE THX ALL ST STANDBY READY ZONE 2 ZONE 3 TEST TONE CH SEL LEVEL- LEVEL+ PURE AUDIO AUDIO SEL DVD VCR/DVR CBL/SAT GAME/TV AUX 1 AUX 2 TAPE TUNER CD PHONO DISPLAY PUSH TO OPEN OPEN/CLOSE VIDEO OFF AUDIO SEL ZONE 2 OFF LEVEL TONE HDMI OUT STEREO THX RT/PTY/TP MEMORY TUNING MODE SETUP TUNING RETURN AUDIO SEL VCR L NIGHT DVD Re-EQ HDD SETUP MIC AUX 2 INPUT PHONES POWER PRESET CLEAR ZONE 3 DIGITAL INPUT LISTENING MODE TUNING ENTER S VIDEO VIDEO L AUDIO R DIGITAL ON OFF RC-690M If you connect a component to more than one audio input, such as a DVD player connected to analog, digital, multichannel, and HDMI inputs, you can use the [AUDIO SEL] button to select which audio input you want to use to listen to that component. [. . . ] · Are you trying to learn from a remote controller that cannot be used for learning?Some commands cannot be learned, especially those that contain several instructions. Tuner Reception is noisy, stereo FM reception suffers from hiss, or the FM STEREO indicator doesn't light up · Relocate your antenna. · When listening to an AM station, operating the remote controller may cause noise. · If nothing improves the reception, install an outdoor antenna. Recording Can't record · On your recorder, make sure the correct input is selected. [. . . ]