User manual ONKYO TX-8511

[. . . ] REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Important Safety Instructions 1. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. [. . . ] · Only the Stereo, Direct, Pure Audio (not North American models), and Mono listening modes can be used with headphones (the listening modes available also depend on the currently selected input source). · When the multichannel input is used, only the front left and right audio can be heard in the headphones. · To adjust the headphone level, press the [CH SEL] button on the remote controller, and then press the [LEVEL +]/[LEVEL -] buttons. You can adjust the level between ­12 dB and +12 dB. 51 Listening to the Radio Using the Tuner With the built-in tuner you can enjoy AM and FM radio stations. I Manual Tuning Mode 1 TUNING MODE Press the [TUNING MODE] button so that the AUTO indicator disappears from the display. Listening to the Radio 2 TUNER TUNING PRESET Use the [TUNER] input selector button to select either AM or FM. Each time you press the [TUNER] button, the input source changes between AM and FM. Press and hold the TUNING Up or Down [ ]/[ ] button. Press the buttons repeatedly to change the frequency one step at a time. Band Frequency The North American models change FM frequency in 0. 2 MHz steps, 10 kHz steps for AM. For other models it's 0. 05 MHz steps for FM and 9 kHz steps for AM. Tuning into weak FM stereo stations If the signal from a stereo FM station is weak, it may be impossible to get good reception. In this case, switch to Manual Tuning mode and listen to the station in mono. I Tuning into Stations by Frequency You can tune into AM and FM stations directly by entering the appropriate frequency. (Actual display depends on country) Tuning into Radio Stations 1 12 I Auto Tuning Mode RECEIVER Press the [RECEIVER] button, followed by the [D TUN] button. D TUN 1 TUNING MODE Press the [TUNING MODE] button so that the AUTO indicator appears on the display. (Actual display depends on country. ) The [RECEIVER] button flashes. If the current radio station is broadcasting TP (Traffic Program), "[TP]" will appear on the display, and traffic news will be heard as and when it's broadcast. If "TP" without square brackets appears, this means that the station is not broadcasting TP. The AV receiver searches until it finds a station that's broadcasting TP. If no stations are found, the message "Not Found" appears. 3 2 RT/PTY/TP Press the [RT/PTY/TP] button twice. Use the PRESET [ ]/[ ] buttons to select the type of program you want. See the table on page 54. ENTER ENTER 3 TUNING PRESET 55 Listening to the Radio--Continued Listening to XM Satellite Radio® (North American models only) Important XM Radio Information To receive XM Radio on this receiver you need to purchase an optional XM Passport System and subscribe to XM's paid programming. Please note that XM is currently only licensed to provide service to the contiguous 48 United States (not available in Alaska and Hawaii) and portions of Canada. XM Radio service is not currently available in Mexico or any other region outside the continental U. S. For updates on service availability please visit XM's website at http://www. xmradio. com or http://www. xmradio. ca Note: Hardware and required basic monthly subscription sold separately. Installation costs and other fees and taxes, including a one-time activation fee may apply. XM offers more than 160 digital channels of audio entertainment, including 100% commercial-free music channels, in the top markets in the U. S. [. . . ] · When listening to an AM station, operating the remote controller may cause noise. · If nothing improves the reception, install an outdoor antenna. Recording Can't record · On your recorder, make sure the correct input is selected (e. g. , digital or analog). · When the Pure Audio listening mode (not North American models) is selected, recording is not possible because no video signals are output. Select another listening mode. Remote Controller The remote controller doesn't work · Make sure that the batteries are installed with the correct polarity (page 12). [. . . ]