User manual ONKYO TX-866

[. . . ] REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Important Safeguards 1. Read Instructions ­ All the safety and operating instructions should be read before the appliance is operated. Retain Instructions ­ The safety and operating instructions should be retained for future reference. [. . . ] The current program type appears on the display. RT/PTY/TP RT/PTY/TP 3. Using the PRESET / buttons, select the PTY program type you desire. "[TP]" will appear if the current station is broadcasting TP signals. Also, if "TP" is displayed, proceed to the next step. PRESET 3. The TX-866E will scan until it reaches a station broadcasting traffic information. If "Not Found" appears on the display, a TP station cannot be located. ENTER 39 Recording a source Input source buttons MASTER VOLUME STANDBY/ON STANDBY POWER ON OFF ZONE 2 ( GRN ) REC ( RED ) PURE AUDIO UPSAMPLING AUDIO SELECTOR DVD VIDEO 1 VIDEO 2 VIDEO 3 VIDEO 4 VIDEO 5 TAPE TUNER PHONO CD NET AUDIO DISPLAY VCR 1 VCR 2 PHONES VIDEO 5 INPUT REC OUT ZONE 2 OFF STEREO SURROUND THX DSP RT/ PTY/ TP MEMORY FM MODE SETUP ENTER RETURN ZONE 2 LEVEL CLEAR TUNING PRESET DIGITAL S VIDEO VIDEO L AUDIO R REC OUT To record the input source signal you are currently watching or listening to This method outputs to the audio and video outputs the currently selected input source signal. This method allows you to a signal while you are actually listening to or watching it. Select the input source to record by pressing the corresponding input source button. The input source is now selected and you may watch or listen to it as desired. Press the REC OUT button repeatedly until "Rec Sel:SOURCE" appears in the front display. The signal from the currently selected input source is now output to the TAPE OUT, VIDEO 1 OUT, VIDEO 2 OUT outputs for recording. · When listening to music in the remote zone (see previous page), you can record the music or video that is being played in the main zone. · If you select FM (or AM) with the TUNER input source button when the recording source is set to AM (or FM), the output for the recording source also changes to AM (or FM). To record an input source signal different from that you are currently watching or listening to Follow the procedure given below to record an input source signal different from that which you are listening to or watching at the time of recording. · You cannot record the surround effects. 41 Enjoying music or videos in the remote zone ZONE 2 indicator MASTER VOLUME STANDBY/ON STANDBY POWER ON OFF ZONE 2 ( GRN ) REC ( RED ) PURE AUDIO UPSAMPLING AUDIO SELECTOR DVD VIDEO 1 VIDEO 2 VIDEO 3 VIDEO 4 VIDEO 5 TAPE TUNER PHONO CD NET AUDIO DISPLAY VCR 1 VCR 2 PHONES VIDEO 5 INPUT REC OUT ZONE 2 OFF STEREO SURROUND THX DSP RT/ PTY/ TP MEMORY FM MODE SETUP ENTER RETURN ZONE 2 LEVEL CLEAR TUNING PRESET DIGITAL S VIDEO VIDEO L AUDIO R OFF Input source buttons ZONE 2 ZONE 2 LEVEL / Using the buttons on the TX-866/900E 1. After pressing the ZONE 2 button, you must press an input source button within 8 seconds. In this condition, even if you change the input source for the main zone, the input source for the remote zone (Zone 2) will not change. Ex. : When the CD button is pressed. To select the same source for the remote zone that is selected for the main zone, press the ZONE 2 button again until "Zone2Sel:SOURCE" appears in the display. In this condition, if you change the input source for the main zone, the input source for the remote zone (Zone 2) will change as well. When "Zone2Sel:Off" is displayed, the output to the remote zone is turned off. Notes: · If a sleep time is set with the SLEEP button, the output to the remote zone will also turn off when the sleep time elapses. If no sound is heard from the selected input source, check if the component is connected to the analog inputs. · If the REC OUT button is pressed in the main room while someone is using the system in the remote zone, the Zone 2 function will be deactivated and the source will turn off in the remote zone. · If you select FM (or AM) with the TUNER input source buttons when the source for the remote zone (Zone 2) is set to AM (or FM), the output for the remote zone also changes to AM (or FM). · 7. 1-channel playback in the main room is disabled if the Surr Back/Zone 2 setting in the Surr Back/Zone 2 sub-menu of the Hardware Setup Menu is set to "Zone 2. " system · When you are using the remote zone (Zone 2), operation will not work. · When you are using the remote zone (Zone 2), the Pure Audio setting will not work. · When you are not using the remote zone (Zone 2), press the ZONE 2 button and then press the OFF button to turn off the ZONE 2 indicator. [. . . ] · "Surr Back/Zone 2" is set to "Zone 2. " © Change the Hardware Setup Surr Back/Zone 2 Sub-menu setting to Surr Back (see page 47). REMOTE CONTROLLER Front panel controls function but remote controller controls do not. · Remote controller is not pointed at the remote sensor of the TXNR900/900E. © Point the remote controller at the remote sensor of the TXNR900/900E (see page 7). © Operate the remote controller within 16 feet (5 meters) (see page 7). [. . . ]