User manual ONKYO TX-DS555

[. . . ] 8 Connecting equipment with 5. 1-channel output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Operation Using the on-screen display . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Assigning a video source to each audio input source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Giving a name to each input source and preset radio station . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Note: The Muting function will be canceled automatically if the receiver is set in the standby mode. Falling asleep with music (Sleep function, remote controller only) You can turn off the power to the TX-DS777/676 automatically after a specified time period. The display shows "Sleep 90min, " which means the receiver automatically enters the standby mode after 90 minutes. Press the SLEEP button repeatedly until the desired sleep time is displayed. Note: Pressing the SLEEP button when the Sleep time display shows 10 minutes or less cancels the Sleep function. Remote controller SPEAKERS A SLEEP STEREO AUTO Adjusting the tone (Bass and treble adjustment) The bass and treble levels can be adjusted in the range of +/-12 in units of 2. You cannot perform this adjustment when the listening mode is "THX" or "Direct. " 1. The display shows "Bass=. " Rotate the SMART SCAN CONTROLLER to adjust the bass level. The display shows "Treble=. " Rotate the SMART SCAN CONTROLLER to adjust the treble level. Press the SMART SCAN CONTROLLER. BASS/ TREBLE 4 * Tone Control * · Adjusting the bass and treble levels with the onscreen display 1. Select "Listening mode Setup" and then press the right edge of the ENTER/Cursor button. Select "Listening Mode" and then press the right edge of the ENTER/Cursor button 4. Select "Tone Control" and then press the right edge of the ENTER/Cursor button. Repeat the above steps until you set the output levels for all speakers. 3 3 3 6 ** Multi Ch Input ** Level Setup Left Center Right Left Sur Left Sur Subwoofer = 0dB = +5dB = 0dB = 0dB = 0dB =+10dB · Using the on-screen display 1. Select "Input Selector" and press the right edge of the ENTER/Cursor button. Press the right or left edge of the ENTER/Cursor button to select "MULTI CH. " Then, press the center of the ENTER/ Cursor button. To assign a video source, select "Video Assign Setup" and then press the right edge of the ENTER/Cursor button. When "Video Assign Setup" screen appears, move the cursor (which is already located at "MULTI CH") rightward or leftward to select the video source you wish to assign. When selected, press the center of the ENTER/Cursor button to return to the previous screen. Select "Level Setup" and press the right edge of the ENTER/ Cursor button. Press the upper or lower edge of the ENTER/Cursor button to select the item. Then, press the right or left edge of the button to select the desired parameter. At the listening position, adjust the speaker output level so that you can hear the same sound volume from all speakers. For the right front, left front, center, right surround and left surround speakers, the output levels can be adjusted within the range of -12 dB/+12 dB. [. . . ] Because the unit contains a microcomputer to provide advanced functions, it may malfunction due to external noise or static electricity. If this happens, press the POWER switch on the unit and then press it in again after about five seconds. 59 Specifications TX-DS777 AMPLIFIER SECTION Continuous Average Power output (FTC) All channels: 105 watts per channel min. RMS at 8 ohms, 2 channels driven from 20 Hz to 20 kHz with no more than 0. 08% total harmonic distortion. RMS at 6 ohms, 2 channels driven from 1 kHz with no more than 0. 1% total harmonic distortion. [. . . ]