User manual ONKYO TX-DS575X

[. . . ] Contents Before using AV Receiver TX-DS575X Instruction Manual Important Safeguards. . . . . . . . . . . . . . . . . . . . . . . . 31 Programming the remote controller codes of other devices into the RC-392M . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Please read this manual thoroughly before making connections and turning on the power. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new AV Receiver. [. . . ] SPEAKERS B: This button turns on or off the speakers connected to the FRONT SPEAKERS B terminals. If you select SPEAKERS B while Surround sound is selected, Surround mode will be automatically canceled. Sleep function (Remote controller only) The sleep timer can turn off the power to the system after a specified time period. To set up this function, use the remote controller supplied with this receiver. Start playing the source you would like to listen to (CD, tape, or radio broadcast). Press the SLEEP button repeatedly to set the duration of time after which you want the system to turn off. Pressing the SLEEP button each time reduces the time value in 10-minute increments. When the specified time comes, the power will be switched off automatically. Disabling the Sleep function Press the SLEEP button until it returns to the selected input source name. or The timer setting will be cancelled if you turn off the power to the unit. Adjusting the tone (BASS, TREBLE) Treble and bass adjustment is effective only for the Front speakers and headphones. TREBLE: Boosts or cuts the treble response. Listening through headphones (PHONES) You can connect stereo headphones to the PHONES jack using a standard stereo plug. If you connect headphones, the unit will enter STEREO mode automatically, and no sound will be produced from the speakers. If you have selected MULTI CH INPUT, you will hear sound only from the FRONT L and R channels. Temporary muting (MUTING) (Remote controller only) Press the MUTING button. The "MUTING" appears on the display and the sound from the speakers or headphones will be switched off by the receiver's audio muting circuits. · press the MUTING button again, or · set the unit to stand-by mode, then turn the power on. To cancel, About volume (VOLUME) You have the option of displaying your volume settings either of two ways: · ABSOLUTE -- on a scale of MIN (0: no sound) to MAX (80: extremely sound); or · RELATIVE -- on a scale which is measured "plus or minus, " relative to the calibrated reference volume. ABSOLUTE: MIN, 1, 2, 3, 4, . . . . . . . , 77, 78, 79, MAX RELATIVE: ­, ­61, ­60, ­59, . . . . . . . , +16, +17, +18 (dB) 1. Press "PRESET/MODE ADJ /®" to select the desired display. · If the speaker level is set to +1dB or higher, the maximum level indicated on the display will change if you raise the volume level. Refer to the following sections for more information on adjusting the speaker level: "Test Tone (Remote controller only)" on page 16. "When Multi channel input is selected as a source" on page 19. 20 Using Listening Mode Before Using Listening Mode Listening Modes The TX-DS575X's surround sound enables you to enjoy the presence of a movie theater or concert hall in your room. Before using a listening mode, make sure the Speaker Setup parameters have been set (refer to page 14). Once the parameters have been set, it is not necessary to set them again. The configuration of the speakers are very important for the surround sound. Refer to "connecting speakers" on page 10. · A system with L/R front and center speakers The following modes are available: DOLBY 3 STEREO The surround channel sound is output from the left and right front speakers. [. . . ] The input selector is not set properly. · · · · · · · · 12 13 13 25 5 5 17 40 Also refer to the respective instruction manuals of the video disc player, video cassette recorder, TV monitor, etc. , that compose your entertainment system. Because the unit contains a microcomputer to provide advanced functions, it may malfunction due to external noise or static electricity. If this happens, press the POWER switch on the unit and then press it in again after about five seconds. Specifications AMPLIFIER SECTION Continuous Average Power output (FTC) All channels: 70 watts per channel min. RMS at 8 ohms, 2 channels driven from 20 Hz to 20 kHz with no more than 0. 08% total harmonic distortion. [. . . ]