User manual ONKYO TX-DS777

[. . . ] Contents Before using A / V Receiver Important Safeguards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 TX-DS777 TX-DS676 Instruction Manual DIMMER FM MUTE/ MODE DOWN TUNING UP CHARACTER/ MEMORY SP/SYS SETUP AUDIO ADJUSTMENT BASS/ TREBLE Preparation Audio equipment connections . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Press the upper or lower edge of the ENTER/Cursor button to select "Bass" or "Treble" and then press the right or left edge of the button to adjust the bass or treble level. Select "Set to Flat" and then press the right edge of the ENTER/ Cursor button to restore the "flat" bass and treble sound. Press the center of the ENTER/Cursor button, or press the EXIT button, to exit the setup mode. Note: You cannot perform this adjustment when the listening mode is "Di31 rect" or "THX (TX-DS777 only). " Bass = 0 Treble = +2 Set To Flat Selecting a preset station 2. Rotate the SMART SCAN CONTROLLER. DIMMER FM MUTE/ MODE DOWN TUNING UP CHARACTER/ MEMORY SP/SYS SETUP AUDIO ADJUSTMENT BASS/ TREBLE MASTER VOLUME STANDBY/ON DO W N MODE UP PRESET/MODE ADJ STAND-BY SMART SCAN CONTROLLER POWER PUSH TO ENTER ON OFF LISTENING MODE DIGITAL/ ANALOG A SPEAKERS B DISPLAY DIRECT STEREO /DTS THX DSP REC OUT CH LEVEL SURROUND MODE PHONES MUL CH INPUT TI VIDEO 4 / VIDEO CAM INPUT DVD VIDEO-1 VIDEO-2 VIDEO-3 VIDEO-4 TAPE FM AM PHONO CD S VIDEO VIDEO L AUDIO R(MONO) AV RECEIVER TX-DS777 1. Press the CH (+ or -) button to select the desired preset number. 3, 4 ** Input Selector ** Input = TUNER Present No. =3 Video Assign Setup IntelliVolume Setup Listening Mode= Orchestra · Using the on-screen display 1. Select "Input Selector" and then press the right edge of the ENTER/Cursor button. Select "Input" and then press the right or left edge of the ENTER/Cursor button to select "TUNER. " 4. Select "Preset No. " and then press the right edge of the ENTER/Cursor button 5. Press the right or left edge of the ENTER/Cursor button to select the desired preset number. Press the center of the ENTER/Cursor button, or press the EXIT button. 1:---2:---3:87. 60 4:---5:---=3 6: 531 7:---8:---9:---10:---- 32 Playing a multichannel input source 1 Remote controller MULTI CH INPUT Setting the MULTI CHANNEL INPUT To play back an input source you connected with the MULTI CHANNEL INPUT connectors, you must set the output level of each speaker. Also, note that this output level setting must be performed independent of the speaker levels you set using the test tone (see page 21). in the multichannel input mode, check again that the source is connected properly (see page 9). If you wish to assign a video source to the multichannel input source, perform the following setting. Press the SP/SYS SETUP button repeatedly until "Video Assign?" appears and then press the SMART SCAN CONTROLLER. Rotate the SMART SCAN CONTROLLER to select the video source you wish to assign and then press the SMART SCAN CONTROLLER. Start playing the component connected to the MULTI CHANNEL INPUT connectors. Press the CH SEL button on the remote controller to select the speaker. At the listening position, adjust the speaker output level so that you can hear the same sound volume from all speakers. For the right front, left front, center, right surround and left surround speakers, the output levels can be adjusted within the range between -12dB ~ +12 dB. [. . . ] Continuous Power output (DIN) 140 watts at 6 ohms Maximum Power output (EIAJ) 170 watts at 6 ohms Total Harmonic Distortion: 0. 08% at rated power (Front) IM Distortion: 0. 08% at rated power (Front) Damping Factor: 60 at 8 ohms (Front) Input Sensitivity and Impedance PHONO: 2. 5 mV, 50 kohms LINE (CD, TAPE, DVD, VIDEO 1, 2, 3, 4): 200 mV, 50 kohms MULTICHANNEL INPUT (FRONT L/R, SURROUND L/R, CENTER): 200 mV, 50 kohms (SUBWOOFER): 36 mV, 50 kohms COAXIAL 1, 2 (DIGITAL): 0. 5 Vp-p, 75 ohms Output Level and Impedance Rec out (TAPE, VIDEO 1): 200 mV, 2. 2 kohms Pre out: 1 V, 470 ohms Phono Overload: 110 mV RMS at 1 kHz, 0. 5% T. H. D. Frequency Response: 20 Hz to 100 kHz, +1/-3 dB(LINE INPUT) RIAA Deviation: 20 Hz to 20 kHz, ±0. 8 dB Tone Control Bass: ±10 dB at 100 Hz Treble: ±10 dB at 10 kHz Signal-to-Noise Ratio Phono: 80 dB (IHF A, 5 mV input) CD/Tape: 100 dB (IHF A) VIDEO SECTION Input sensitivity/Impedance (DVD, VIDEO 1, 2, 3, 4) VIDEO (Composite): Output Level/Impedance (VIDEO 1, 2, MONITOR) VIDEO (Composite): TX-DS676 AMPLIFIER SECTION Continuous Average Power output (FTC) All channels: 85 watts per channel min. RMS at 8 ohms, 2 channels driven from 20 Hz to 20 kHz with no more than 0. 08% total harmonic distortion. RMS at 6 ohms, 2 channels driven from 1 kHz with no more than 0. 1% total harmonic distortion. [. . . ]