User manual ONKYO TX-NR5000E

[. . . ] Contents AV Receiver Getting Started 2 TX-NR1000 TX-NR5000E Instruction Manual Installation and Connections 18 Operations 48 Setup Menu 82 Using the Remote Controller Thank you for purchasing an Onkyo AV Receiver. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new AV Receiver. Please retain this manual for future reference. 124 Miscellaneous 143 En WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). [. . . ] Notch Filter Off (Default): Select this setting when not applying the notch filter. Frequency When setting "Notch Filter" above to "On, " the notch filer becomes effective at the frequency you specify here. With your measuring device, the frequency value can be set at 1 Hz intervals in a range from 20 Hz to 300 Hz. The default is 100 Hz. 90 Speaker/Output Setup--Continued THX Audio Setup Sub-menu This is for setting up a home theater with a THX-Ultra2 compliant speaker system. These settings will be effective in the listening mode for the THX Ultra2 Cinema and THX Music Mode. The settings in the THX Audio Setup sub-menu can be configured for both "Main A" and "Main B. " THX Ultra2 Subwoofer A/ THX Ultra2 Subwoofer B This is for setting the connected subwoofer. Select "Yes" or "No" according to your subwoofer's specification. Yes: Set "Yes" if your subwoofer conforms to the THX Ultra2 standard or if the playback capability of its bass range extends down to 20 Hz. Otherwise, set "No. " No (Default): Set "No" if you use any subwoofer that does not fit the conditions above. · For any speaker that is not available or set to "Not Used" in the Speaker Configuration sub-menu, no associated setting item is displayed. Boundary Gain Compensation A/ Boundary Gain Compensation B This is for setting the correction of boundary gains. This item can be set when "THX Ultra2 Subwoofer" is set to "Yes. " Room boundaries (walls) or other characteristics (such as construction materials) may increase the perceived acoustics levels at low frequencies. Depending on the listener's and the subwoofer's position, the listener may experience an excessive bass effect. The purpose of this feature is to compensate for excessive bass resulting from a boundary gain effect. Distance Between Surr Back A SP/ Distance Between Surr Back B SP This setting is allowed only when "Main 2ch" is selected from the Speaker Configuration sub-menu. Place two surround back speakers as close together as possible, measure the distance, and set the value (See the figure). 1-4 ft (0. 3-1. 2 m): This is the setting when the distance between speakers is 1-4 feet (30 cm-1. 2 m). >4 ft (1. 2 m): This is the setting when the distance between speakers is 4 feet (1. 2 m) or more. *ASA: Advanced Speaker Array Audio Output Assign Sub-menu This setting allocates audio output jacks on the TX-NR1000/TX-NR5000E to input (play) sources. The TX-NR1000/TX-NR5000E is equipped with analog output jacks for five lines, and digital output jacks: optical jacks (OPT) for two lines, and coaxial jacks (COAX) for two lines. If setting the analog jacks to "Zone 2 Out" or "Zone 3 Out, " you can also specify whether output should be variable or fixed. The default settings are as follows: Terminals Analog 1 (AUDIO OUT 1) Analog 2 (AUDIO OUT 2) Analog 3 (AUDIO OUT 3) Analog 4 (AUDIO OUT 4) Analog 5 (AUDIO OUT 5) Opt 1 Out (DIGITAL OUT OPTICAL 1) Opt 2 Out (DIGITAL OUT OPTICAL 2) Default input settings Video 1 Rec Out Video 2 Rec Out Video 3 Rec Out Zone 2 Out Zone 3 Out Tape 1 Rec Out Tape 2 Rec Out Coax 1 Out (DIGITAL OUT COAXIAL 1) Video 1 Rec Out Coax 2 Out (DIGITAL OUT COAXIAL 2) Zone 2 Out Analog 1-5 Set the analog audio output jacks of "AUDIO OUT 1-5. " You can select from Tape 1 Rec Out, Tape 2 Rec Out, Video 1 Rec Out, Video 2 Rec Out, Video 3 Rec Out, Zone 2 Out, Zone 3 Out, and Not Used. AUDIO 1 2 4 3 5 R L OUT R L Example 1: When input (REC) of a sound recording device (e. g. , a cassette deck) with TAPE 1 as an input source is connected to AUDIO OUT 1, set "Analog 1" to "Tape 1 Rec Out. " Example 2: When sound input of a picture recording device (e. g. , a VCR) with VIDEO 1 as an input source is connected to AUDIO OUT 2, set "Analog 2" to "Video 1 Rec Out. " Example 3: When the amplifier for Zone 2 is connected to AUDIO OUT 5, set "Analog 5" to "Zone 2 Out. " When nothing is connected: Select "Not Used. " 0-1 ft (0-0. 3 m)(Default): This is the setting when the distance between the speakers is 0-1 foot (0-30 cm). 91 Speaker/Output Setup--Continued Zone 2 Out, Zone 3 Out This item is displayed when "Zone 2 Out" or "Zone 3 Out" is specified for Analog 1-5 above. [. . . ] "Not available with NET AUDIO use" · Operation not possible with Net Audio selected for the input source. "Not available with Dolby Headphone Off" · Doesn't work with the Dolby Headphone function off. "Not available with Dolby Headphone On" · Doesn't work with the Dolby Headphone function on. "Not available with zone2 out in Line out" · Operation not possible with "1-8. f. [. . . ]