User manual ONKYO TX-SR502E

[. . . ] 2 AV Receiver TX-SR502 TX-SR502E Instruction Manual Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new AV Receiver. Please retain this manual for future reference. Advanced Operation . . . . . . . . . . . . . . . . . . . . . [. . . ] With this function you can assign digital audio inputs to input sources. You only need to change these assignments if your connections don't match the default assignments listed below. Input source DVD VIDEO 1 VIDEO 2 VIDEO 3 TAPE CD DIGITAL INPUT OPT1 (OPTICAL 1) - - - - (Analog) OPT2 (OPTICAL 2) - - - - (Analog) OPT3 (OPTICAL 3) COAX (COAXIAL) 1 POWER ON OFF Set the [POWER] switch to the ON position ( ). (Skip this step if you have American model. ) The TX-SR502/TX-SR502E enters Standby mode, and the STANDBY indicator comes on. Note: · The remote controller has no effect while the [POWER] switch in the OFF position. Alternatively, press the remote controller's [AMP] button followed by the [ON] button. The TX-SR502/TX-SR502E comes on, the display lights up, and the STANDBY indicator goes off. To prevent any loud surprises the next time you turn on your TX-SR502/ TX-SR502E, always turn down the volume before turning it off. 2 STANDBY/ON Remote controller ON STANDBY For example, if you connect your DVD player to the COAXIAL DIGITAL IN, you'll need to change the DVD input source from OPT 1 to COAX, and change the CD input source to something other than COAX. If you want to use the TAPE input source with only the analog TAPE IN sockets, you'll need to change the TAPE assignment from "OPT3" to "----" (Analog). You can change the assignments as follows. 1 TAPE DVD VIDEO 1 VCR VIDEO 2 VIDEO 3 Notes: (not for the American model) · The TX-SR502/TX-SR502E is shipped with the POWER switch in the ON position ( ). When the power cord is connected for the very first time, the TX-SR502/TX-SR502E will enter Standby and the STANDBY indicator will light up. · To completely shutdown the TX-SR502/TX-SR502E, set the POWER switch to the OFF position ( ). CD Press the input selector button for the source that you want to assign. (Digital inputs cannot be assigned to the TUNER input source. ) 2 DIGITAL INPUT Press the [DIGITAL INPUT] button. The current assignment appears. 3 DIGITAL INPUT Press the [DIGITAL INPUT] button repeatedly to select COAX, OPT1, OPT2, OPT3, or ­ ­ ­ ­. 31 First Time Setup--Continued Speaker Configuration This section explains how to specify which speakers are connected and their sizes. For speakers with a cone diameter larger than 6-1/2 inches (16 cm), specify Large. For those with a smaller diameter, specify Small. Cone diameter 3 ENTER While the Subwoofer setting is selected, use the Left and Right [ ]/[ ] buttons to select Yes or No. Use the Down [ ] button to select "Front, " and then use the Left and Right [ ]/[ ] buttons to select Small or Large. Note: · If the Subwoofer setting in step 3 is set to No, this setting is fixed at Large and does not appear. Use the Down[ ] button to select "Center, " and then use the Left and Right [ ]/[ ] buttons to select Small, Large, or None. Note: · If the Front setting in step 4 is set to Small, the Large option cannot be selected. Use the Down[ ] button to select "Surround, " and then use the Left and Right [ ]/[ ] buttons to select Small, Large, or None. Note: · If the Front setting in step 4 is set to Small, the Large option cannot be selected. 4 ENTER ON STANDBY I TV INPUT V1 V2 V3 1 DVD 2 MULTI CH 3 6 TUNER + TV CH 4 CD 5 TAPE - 7 +10 --/--TONE 8 0 9 T V VOL CLEAR ENTER _ TUNER/ TAPE + MD AMP REMOTE MODE DVD CD CDR AMP TV VCR CABLE SAT DIMMER TV INPUT P TO M SLEEP ENU MEN U ENTER PREV CH + CH DISC ENTER VOL EX IT RE E GUID TUR N UP SET SETUP MUTING 5 ENTER DISPLAY REC SP A SP B RANDOM AUDIO SURR SUBTITLE ALL ST ANGLE LAST M STEREO REPEAT A-B DIRECT SEARCH DSP MEMORY DSP ENTER 1 AMP Press the [AMP] button followed by the [SETUP] button. 6 2 ENTER Use the Up and Down [ ]/[ ] buttons to select "1. SP Config, " and then press the [ENTER] button. ENTER ENTER ENTER 32 First Time Setup--Continued 7 ENTER ENTER Use the Down [ ] button to select "Surr Back, " and use the Left and Right [ ]/[ ] buttons to select Small, Large, or None. [. . . ] Installing an outdoor antenna is a specialist job, so contact your nearest dealer for advice (page 19). The power cord must be plugged into a wall outlet a few times each month in order to preserve the presets. To prevent signal loops and damage to the TX-SR502/TX-SR502E, input signals are not fed through to outputs with the same name (e. g. , TAPE IN/OUT or VIDEO 1 IN/ OUT). Although you cannot record Dolby Digital or DTS surround channels, you can record the left and right channels by connecting the source AV component's analog left and right outputs to a pair of analog inputs on the TX-SR502/TX-SR502E. [. . . ]