User manual ONKYO TX-SR602E

[. . . ] 2 AV Receiver TX-SR702/702E TX-SR602/602E TX-SR8260 Instruction Manual Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . Please read this manual thoroughly before making any connections and plugging it in. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new AV Receiver. Please retain this manual for future reference. Using the Remote Controller with Other Components . . . . . . [. . . ] C: LFE channel for subwoofer (1 means yes). 55 Basic Operation--Continued Using the Tuner With the built-in tuner you can enjoy AM and FM radio stations. Manual Tuning Mode 1 Press the [TUNING MODE] button so that the AUTO indicator disappears from the display. Listening to the Radio 2 1 Use the [TUNER] input selector button to select either AM or FM. In this example, FM has been selected. Press and hold the TUNING Up or Down [ ]/[ ] button. Press the buttons repeatedly to change the frequency one step at a time. Band Frequency (Actual display depends on country. ) The American model changes FM frequency in 0. 2 MHz steps, 10 kHz steps for AM. For other models it's 0. 05 MHz steps for FM and 9 kHz steps for AM. Tuning into weak FM stereo stations If the signal from a stereo FM station is weak, it may be impossible to get good reception. In this case, switch to Manual Tuning mode and listen to the station in mono. Tuning into Radio Stations 12 Auto Tuning Mode 1 Press the [TUNING MODE] button so that the AUTO indicator appears on the display. 2 Press the TUNING Up or Down [ ]/[ ] button. Searching stops when a station is found. When tuned into a station, the TUNED indicator appears. When tuned into a stereo FM station, the FM STEREO indicator appears on the display, as shown. TUNED AUTO FM STEREO 56 Basic Operation--Continued Presetting Radio Stations Deleting Presets 2, 4 3 2 You can store up to 40 of your favorite radio stations as presets. 1 2 1 2 Tune into the station that you want to store as a preset. The MEMORY indicator appears and the preset number flashes. Select the preset that you want to delete. While holding down the [MEMORY] button, press the [TUNING MODE] button. The selected preset is deleted and its number disappears from the display. 3 While the MEMORY indicator is displayed (about 8 seconds), use the PRESET [ ]/[ ] buttons to select a preset from 1 through 40. In this example, preset #3 is selected. Displaying Radio Information 2 4 Press the [MEMORY] button again to store the station. Repeat this procedure for all your favorite radio stations. 1 Press the [DISPLAY] button repeatedly to cycle through the available information. Selecting Preset Stations 1 Use the [TUNER] input selector button to select either AM or FM. Band, preset # & frequency Listening mode 2 Use the PRESET [ ]/[ ] buttons, or the remote controller's CH [+/­] button to select a preset. 57 Basic Operation--Continued Using RDS (European models only) RDS only works with European models and only in areas where RDS broadcasts are available. RDS stands for Radio Data System and it's a method of transmitting data in FM radio signals. It was developed by the European Broadcasting Union (EBU) and is available in most European countries. In addition to displaying text information, RDS can also help you find radio stations by type (e. g. , news, sport, rock, etc). The AV receiver supports four types of RDS information: PS (Program Service) Program Types Used in Europe (PTY) Type None News reports Current affairs Display NONE NEWS AFFAIRS Description No program type. Topical reporting of current affairs, often with a wider range of topics than news reports. General information such as weather forecasts, consumer affairs, medical help, etc. Radio plays and serials. Information INFO Sport Education Drama Culture SPORT When tuned to an RDS station that's broadcasting PS information, the station's name appears. When you press the [DISPLAY] button, the frequency is displayed for three seconds. RT (Radio Text) EDUCATE Formal educational programs. [. . . ] · Make sure you've entered the correct remote control code. · If it's an Onkyo component, make sure that the cable and analog audio cable are connected properly. · Make sure you've selected the correct remote controller mode (page 14). · If you connect an MD recorder or CD recorder to the TAPE jacks, be sure to set make the necessary setting (pages 52 and 80). [. . . ]