User manual ONKYO TX-SR603

[. . . ] 2 AV Receiver TX-SR603/603E TX-SR8360 Instruction Manual Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . Please read this manual thoroughly before making any connections and plugging it in. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new AV Receiver. Please retain this manual for future reference. Using the Remote Controller with Other Components . . . . . . [. . . ] The main menu appears onscreen. 5 ENTER 2 ENTER Use the Up and Down [ ]/[ ] buttons to select "5. The Equalizer Settings menu appears. Use the Up and Down [ ]/[ ] buttons to select a frequency, and then use the Left and Right [ ]/[ ] buttons to adjust the level at that frequency. The volume at each frequency can be adjusted from ­6 to +6 dB in 1 dB steps. Tip: Low frequencies (e. g. , 80 Hz) affect bass sounds; high frequencies (e. g. , 8 kHz) affect treble sounds. Use the Up [ ] button to select "Channel, " and then use the Left and Right [ ]/[ ] buttons to select another speaker. The setup menu closes. 6 ENTER 7 Note: This procedure can also be performed on the AV receiver by using its [SETUP] button, arrow buttons, and [ENTER] button. 51 First Time Setup--Continued Changing the TAPE/MD/CDR Display If you connect an -compatible Onkyo MiniDisc recorder or CD recorder to the TAPE IN/OUT jacks, for to work properly, you must change this setting. This setting can only be changed on the AV receiver. 1, 2 1 TAPE Press the [TAPE] input selector button so that "TAPE" appears on the display. 2 TAPE Press and hold down the [TAPE] input selector button (about 3 seconds) to set the display. Repeat this step to select TAPE, MD, or CDR. 52 Basic Operations Selecting the Input Source This section explains how to select the input source (i. e. , the AV component that you want to listen to or watch). 3 1 1 3 1 1 AV receiver MLUTI CH DVD VIDEO 1 VCR 1 Remote controller RECEIVER Use the AV receiver's input selector buttons to select the input source. To select the input source with the remote controller, press the [RECEIVER] button, and then use the INPUT SELECTOR buttons. On the remote controller, the [V1], [V2], [V3], and [V4] buttons select the VIDEO 1, VIDEO 2, VIDEO 3, and VIDEO 4 input sources, respectively. or VIDEO 2 VIDEO 3 VIDEO 4 VCR 2 TAPE TUNER CD 2 Start playback on the source component. When you select DVD or another video component, on your TV, you'll need to select the video input that's connected to the AV receiver's MONITOR OUT. On some DVD players, you may need to turn on the digital audio output. Remote controller 3 AV receiver MASTER VOLUME or VOL To adjust the volume, use the MASTER VOLUME control, or the remote controller's [VOL] button. It has a wide volume range, allowing precise adjustment. 53 Basic Operations--Continued Using the Sleep Timer With the sleep timer, you can set the AV receiver to turn off automatically after a specified period. Press [RECEIVER] first DIMMER SLEEP SLEEP RECEIVER Press the [RECEIVER] button, and then press the [SLEEP] button repeatedly to select the required sleep time. The SLEEP indicator appears on the display when the sleep timer has been set. The specified sleep time appears on the display for about five seconds, then the previous display reappears. MUTING Setting the Display Brightness You can adjust the brightness of the display. RECEIVER If you need to cancel the sleep timer, press the [SLEEP] button repeatedly until the SLEEP indicator disappears. To check the time remaining until the AV receiver sleeps, press the [SLEEP] button. Note that if you press the [SLEEP] button while the sleep time is being displayed, you'll shorten the sleep time by 10 minutes. DIMMER Press the [RECEIVER] button, and then press the [DIMMER] button repeatedly to select: · Normal+VOLUME light on. · Dimmer+VOLUME light off. Using Headphones You can connect a pair of stereo headphones (1/4-inch phone plug) to the AV receiver's PHONES jack for private listening, as shown. Muting the AV Receiver You can temporarily mute the output of the AV receiver. The output is muted and the MUTING indicator flashes on the display, as shown. PHONES RECEIVER MUTING To unmute the AV receiver, press the [MUTING] button again, or adjust the volume. The Mute function is cancelled when the AV receiver is set to Standby. Notes: · Always turn down the volume before connecting your headphones. · The speakers are turned off while the headphones plug is inserted in the PHONES jack (Zone 2 speakers are not turned off). · When you connect a pair of headphones, the listening mode is set to Stereo, unless it's already set to Stereo, Mono, Direct, or Pure Audio (not North American TX-SR603). [. . . ] · If it's an Onkyo component, make sure that the cable and analog audio cable are connected properly. · Make sure you've selected the correct remote controller mode (pages 14-19). · If you connect an MD recorder or CD recorder to the TAPE jacks, be sure to make the necessary setting (pages 52 and 78). Recording Can't record?· On your recorder, make sure the correct input is selected (e. g. , digital or analog). Zone 2 Zone 2 has turned off? [. . . ]