User manual ONKYO TX-SR607

[. . . ] Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 AV Receiver Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 TX-SR607 Turning On & First Time Setup . . . . . 38 Instruction Manual Basic Operations. . . . . . . . . . . . . . . . . . . . . . . . . 51 Using the Listening Modes . . . . . . . . 62 Advanced Setup . . . . . . . . . . . . . . . . . . . . . . . . . . 69 Zone 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 Controlling Other Components . . . . 89 Thank you for purchasing an Onkyo AV Receiver. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new AV Receiver. Please retain this manual for future reference. Others. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 En WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). [. . . ] The AV receiver's input source will automatically be set to the [PORT] selector. Notes: · To use this function, your iPod must be in the UP-A1 series Dock, and the UP-A1 series Dock must be connected to the AV receiver. · When you use this function, be sure to set the AV receiver's volume control to a suitable level. · The AV receiver may take several seconds to startup, so you might not hear the first few seconds of the first song. Charging Your iPod models Battery The UP-A1 series Dock charges your iPod models battery while your iPod is in the UP-A1 series Dock and connected to the UNIVERSAL PORT jacks on the AV receiver. While your iPod is seated in the UP-A1 series Dock, its battery will be charged when the AV receiver is set to "On" or "Standby". Note: When UP-A1 series Dock that seated iPod is connected, the power consumption on standby mode slightly increases. Controlling iPod By pressing the REMOTE MODE button that's been programmed with the remote control code for your Dock, you can control your iPod in the Dock with the following buttons. The [PORT] button is preprogrammed with the remote control code for controlling a Dock with Universal Port connector. When Using a Dock with Universal Port connector: · Connect the Dock to the UNIVERSAL PORT jack. · See to the Dock's instruction manual for more information. You can control your iPod when "PORT" is selected as the input source. Press [PORT] button first Note: For detailed operation of the iPod, please refer to the instruction manual. 59 UP-A1 series Dock for iPod--Continued Arrow [ ]/[ ] and ENTER buttons Used to navigate menus and select items. PLAYLIST [ ]/[ ] buttons Selects the previous or next playlist on the iPod. Your iPod is properly stationed in a UP-A1 series Dock connected to the UNIVERSAL PORT jack of this unit, and the connection between your iPod and this unit is complete. When connection is confirmed, "UP-A1" is displayed for about 8 seconds. UP-A1 series Dock is not connected The iPod being used is not supported by this unit. UP-A1 series Dock is connected This unit is in the middle of recognizing the connection with your iPod. UP-A1 series Dock does not support the control Status messages Note: In case of a transmission error without a status message appearing in the front panel, check the connection to your iPod. UP-A1 series Dock in connection with the check Your iPod was removed from a UP-A1 series Dock connected to the UNIVERSAL PORT jack of this unit. Station your iPod back in a UP-A1 series Dock connected to the UNIVERSAL PORT jack of this unit. 60 Recording This section explains how to record the selected input source to a component with recording capability, and how to record audio and video from different sources. Notes: · The surround sound and DSP listening modes cannot be recorded. · DTS signals will be recorded as noise, so don't attempt analog recording of DTS CDs or LDs. · While the listening mode is set to Pure Audio, no image is provided because the power is turned off for the video circuit. [. . . ] (Pure Audio listening mode is not available for North American/Taiwan models. ) The display doesn't work · The display is turned off when the Pure Audio listening mode is selected. How do I change the language of a multiplex source · Use the "Multiplex" setting on the "Audio Adjust" menu to select "Main" or "Sub" (page 73). The functions don't work · To use , you must make an connection and an analog audio connection (RCA) between the component and AV receiver, even if they are connected digitally (page 37). The functions Auto Power On/Standby and Direct Change don't work for components connected via · These functions don't work when Zone 2 is turned on. [. . . ]