User manual ONKYO TX-SR608

[. . . ] Contents AV Receiver Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 TX-SR608 Instruction Manual Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Turning On & Basic Operations . . . . . . 22 Advanced Operations . . . . . . . . . . . . . . . . . 38 Controlling iPod & Other Components. . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Others. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Thank you for purchasing an Onkyo AV Receiver. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new AV Receiver. Please retain this manual for future reference. En WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). [. . . ] The LPF only applies to sources that use the LFE channel. Note · If you're using THX-certified speakers, select "80Hz". Here you can adjust the level of each speaker with the built-in test tone so that the volume of each speaker is the same at the listening position. Left, Front Wide Left, Front High Left, Center*1, Front High Right, Front Wide Right, Right, Surr Right, Surr Back Right, Surr Back Left, Surr Left ­12dB to 0dB to +12dB in 1 dB step. Subwoofer*1 ­15dB to 0dB to +12dB in 1 dB step. Note · Speakers that you set to "No" or "None" in the "Speaker Configuration" cannot be selected ( 41). · The speakers cannot be calibrated while the AV receiver is muted. · The test tone is output at the standard level for THX, which is 0 dB (absolute volume setting 82). If you normally listen at volume settings below this, be careful because the test tone will be much louder. *1 For the center speaker and subwoofer, the level settings made by using the Home menu are saved ( 24). Tip · If you're using a handheld sound level meter, adjust the level of each speaker so that it reads 75 dB SPL at the listening position, measured with C-weighting and slow reading. Double Bass This setting is set automatically by Audyssey 2EQ® Room Correction and Speaker Setup function ( 25). With the Double Bass function, you can boost bass output by feeding bass sounds from the front left, right, and center channels to the subwoofer. Off: Double Bass function off. Note · This function can be set only if the "Subwoofer" setting is set to "Yes", and the "Front" setting is set to "Full Band". · If you're using THX-certified speakers, select "Off". Equalizer Settings This setting is set automatically by Audyssey 2EQ Room Correction and Speaker Setup function ( 25). With the Equalizer settings, you can adjust the tone of speakers individually with a 5-band equalizer. Equalizer Manual: You can adjust the equalizer for each speaker manually. If you selected "Manual", continue with this procedure. Speaker Distance This setting is set automatically by Audyssey 2EQ Room Correction and Speaker Setup function ( 25). Here you can specify the distance from each speaker to the listening position so that the sound from each speaker arrives at the listener's ears as the sound designer intended. (The default setting varies from country to country. ) Left, Front Wide Left, Front High Left, Center, Front High Right, Front Wide Right, Right, Surr Right, Surr Back Right, Surr Back Left, Surr Left, Subwoofer Specify the distance from the each speaker to your listening position. Note · Speakers that you set to "No" or "None" in the Speaker Configuration cannot be selected ( 41). 1 2 Press to select "Channel", and then use to select a speaker. / Use / to select a frequency, and then use the / to adjust the level at that frequency. The volume at each frequency can be adjusted from ­6dB to 0dB to +6dB in 1 dB steps. Tip · Low frequencies (e. g. , 63Hz) affect bass sounds; high frequencies (e. g. , 16000Hz) affect treble sounds. 3 Level Calibration This setting is set automatically by Audyssey 2EQ Room Correction and Speaker Setup function ( 25). Use to select "Channel", and then use / to select another speaker. You cannot select speakers that you set to "No" or "None" in the "Speaker Configuration" ( 41). En 42 Audyssey: This is selected automatically by Audyssey 2EQ® Room Correction and Speaker Setup function. The Audyssey Dynamic Volume indicator will light ( 9) and "Dynamic EQ" and "Dynamic Volume" become available ( 45). Off: No Audyssey 2EQ equalizing will apply. Note · You can select: "63Hz", "250Hz", "1000Hz", "4000Hz", or "16000Hz". And for the subwoofer, "25Hz", "40Hz", "63Hz", "100Hz", or "160Hz". · While the Direct or Pure Audio (European, Australian, and Asian models) listening mode is selected, the equalizer settings have no effect. [. . . ] Connect the audio output from the TV to the OPTICAL IN 2 jack of the AV receiver using an optical digital cable. Note · When the audio return channel (ARC) function is used with TV for HDMI 1. 4, it should not be this connection ( 52). Confirm the settings. Turn off the power of the TV, and confirm that the power of the connected components is turned off automatically with the link operation. Start playback of the Blu-ray Disc/DVD player/ recorder, and confirm the following. · The power of the AV receiver is turned on automatically, and input with the Blu-ray Disc/DVD player/recorder connected is selected. [. . . ]