User manual ONKYO TX-SR803E

[. . . ] 2 AV Receiver TX-SR803/803E TX-SR703/703E TX-SR8370 Instruction Manual Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new AV Receiver. Please retain this manual for future reference. Advanced Operation . . . . . . . . . . . . . . . . . . . . . [. . . ] If you find that your subwoofer is too loud, try the +10 dB or +15 dB setting. Note: · While the multichannel DVD input is selected, the Speaker Configuration settings on page 70 are ignored, and signals from the multichannel DVD input are fed to the subwoofer, front left, front right, center, surround left, surround right, surround back left, and surround back right speakers as they are. 57 Common Functions This section explains functions that can be used with any input source. V1 V2 V3 Adjusting Speaker Levels You can adjust the volume of each speaker while listening to an input source. These temporary adjustments are cancelled when the AV receiver is set to Standby. 1 V4 2 MULTI CH 3 DVD + T V CH 4 CD 5 TAPE 6 TUNER - 7 PHONO 8 0 MACRO 9 T V VOL CLEAR 12 +10 11 --/--- 10 INPUT SELECTOR Press [RECEIVER] first DIMMER 1 ZONE2 1 2 3 REMOTE MODE RECEIVER TAPE/AMP TV VCR CABLE CDR SAT MD DVD CD HDD CH SEL DIMMER P TO U MEN MEN U SLEEP Use the remote controller's [CH SEL] button to select each speaker, and use the [LEVEL­] and [LEVEL+] buttons to adjust the volume. You can adjust the volume of each speaker from ­12 dB to +12 dB (­15 dB to +12 dB for the subwoofer). SLEEP LEVEL LEVEL VOL + CH DISC ALBUM ENTER - DISPLAY PREV CH DISPLAY RE TU R N SE T UP MUTING MUTING REC PLAYLIST RANDOM LISTENING MODE STEREO REPEAT PURE A SURR AUDIO DIRECT SUBTITLE PLAY MODE THX ALLST CH SEL TEST TONE CH SEL LEVEL LEVEL OPEN/CLOSE VIDEO OFF L NIGHT Re-EQ LEVEL ­ + Notes: · You cannot use this function while the AV receiver is muted. · Speakers that are set to No or None in the Speaker Configuration cannot be adjusted. Headphones While a pair of headphones is connected, you can adjust the volume of each headphone speaker, from ­12 dB to +12 dB each. RC-620M MASTER VOLUME STANDBY/ON STANDBY ZONE 2 POWER ON OFF PURE AUDIO MULTI CH DVD VIDEO 1 VIDEO 2 VIDEO 3 VIDEO 4 PHONO TAPE TUNER CD DISPLAY PHONES ZONE 2 OFF TONE STEREO DIMMER MEMORY TUNING MODE VIDEO 4 INPUT SETUP RETURN ENTER SETUP MIC LISTENING MODE ZONE 2 LEVEL CLEAR PRESET TUNING PRESET DIGITAL S VIDEO VIDEO L AUDIO R · These settings are stored when the AV receiver is set to Standby. PHONES DIMMER DISPLAY Muting the AV Receiver You can temporarily mute the output of the AV receiver. Setting the Display Brightness You can adjust the brightness of the display. MUTING Remote controller DIMMER AV receiver DIMMER Press the remote controller's [DIMMER] button repeatedly to select: · Normal + VOLUME light on. You can also use the AV receiver's [DIMMER] button (not European models). Press the remote controller's [MUTING] button. The output is muted and the MUTING indicator flashes on the display. To unmute the AV receiver, press the remote controller's [MUTING] button again, or adjust the volume. Tip: You can choose how much the output is muted by using the Muting Level preference (see page 78). 58 Common Functions--Continued Using the Sleep Timer With the sleep timer, you can set the AV receiver so that it turns off automatically after a specified period. SLEEP Displaying Source Information You can display various information about the current input source as follows. Remote controller Press the remote controller's [SLEEP] button repeatedly to select the required sleep time. The SLEEP indicator appears on the display when the sleep timer has been set, as shown. The specified sleep time appears on the display for about 5 seconds, then the previous display reappears. SLEEP indicator DISPLAY Press the [DISPLAY] button repeatedly to cycle through the available information. AV receiver DISPLAY The following information can typically be displayed: Input source & volume Signal format* or sampling frequency Input source & listening mode To cancel the sleep timer, press the [SLEEP] button repeatedly until the SLEEP indicator disappears. Note that if you press the [SLEEP] button while the sleep time is being displayed, you'll shorten the sleep time by 10 minutes. Using Headphones For private listening, you can connect a pair of stereo headphones (1/4-inch phone plug) to the AV receiver's PHONES jack. STANDBY/ON STANDBY ZONE 2 *If the input signal is analog, no format information is displayed. If the input signal is digital but not PCM, the signal format is displayed. On the TX-SR803/803E, if the input signal is multichannel PCM, the sampling frequency and signal format will be displayed. Information is displayed for about 3 seconds, then the previous display reappears. Interpreting Surround Channel Information POWER ON OFF PURE AUDIO A ZONE 2 OFF BC PHONES Notes: · Always turn down the volume before connecting your headphones. · The speakers are turned off while the headphones plug is inserted in the PHONES jack. (The Zone 2 speakers are unaffected. ) · When you connect a pair of headphones, the listening mode is set to Stereo, unless it was set to Pure Audio, Mono, Stereo, or Direct, in which case it stays the same. A: The number of front channels (front left, front right, and center). B: The number of surround channels (surround left and surround right). If there's surround back channel information, this number will be 3. C: LFE channel for subwoofer (1 means yes). 59 Using the Listening Modes Selecting the Listening Modes For a description of each listening mode, see "About the Listening Modes" on page 62. · The Dolby Digital and DTS listening modes can only be selected if your DVD player is connected to the AV receiver with a digital audio connection (coaxial, optical, or HDMI). · Listening mode availability depends on the format of the current input signal. · While a pair of headphones is connected, you can only select the Pure Audio, Mono, Direct, or Stereo listening mode. SURR LISTENING MODE Selecting with the Remote Controller P TO MEN U MEN U + CH DISC ALBUM ENTER VOL PREV CH DISPLAY RE TU R N SE T UP MUTING REC PLAYLIST RANDOM STEREO PURE A DIRECT , ALLST STEREO REPEAT PURE A SURR AUDIO DIRECT SUBTITLE PLAY MODE THX ALL ST THX TEST TONE CH SEL LEVEL LEVEL OPEN/CLOSE VIDEO OFF L NIGHT Re-EQ RC-620M Selecting on the AV Receiver STEREO MASTER VOLUME STANDBY/ON STANDBY ZONE 2 [STEREO] button This button selects the Stereo listening mode. [. . . ] To reset the AV receiver to its factory defaults, turn it on and, while holding down the [VIDEO 1] button, press the [STANDBY/ON] button. "Clear" will appear on the display and the AV receiver will enter Standby mode. For North American and Australian models, set the AV receiver to Standby before disconnecting the power cord from the wall outlet. For other models, set the AV receiver to Standby and the POWER switch to OFF before disconnect the power cord. 94 Specification Amplifier Section Power Output TX-SR803/803E: 2 channels driven: General Power Supply North American: AC 120 V, 60 Hz Australian and European: AC 230-240 V, 50 Hz Others: AC 120/220-240 V, 50/60 Hz AC 230-240 V, 50Hz AC 220-230 V, 50/60 Hz North American: 7. 5 A Others: 680 W North American: 0. 1 W Australian and European: 0. 2 W Others: 0. 5 W 435 × 173. 5 × 430 mm 17-1/8" × 6-13/16" × 16-15/16" North American: 13. 3 kg 29. 3 lbs. [. . . ]