User manual ONKYO TXSR805-S Supplementary Guide

[. . . ] 54 En WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Important Safety Instructions 1. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. [. . . ] Use the Down [ ] button to select "Front, " and then use the Left and Right [ ]/[ ] buttons to select Small or Large. Note: · If the Subwoofer setting in step 3 is set to No, this setting is fixed at Large and does not appear. DISC CH VOL 4 TOP MENU MENU SP A / B MUTING 2­8 RETURN RETURN ENTER SETUP 1, 9 LISTENING MODE STEREO SURROUND AUDIO SUBTITLE RANDOM REPEAT TEST TONE CH SEL PLAY MODE DISPLAY L NIGHT CINE FLTR LEVELLEVEL+ RC-605S 5 1 Press the [RECEIVER] button followed by the [SETUP] button. Use the Down [ ] button to select "Center, " and then use the Left and Right [ ]/[ ] buttons to select Small, Large, or None. Note: · If the Front setting in step 4 is set to Small, the Large option cannot be selected. 32 First Time Setup--Continued 6 Use the Down [ ] button to select "Surround, " and then use the Left and Right [ ]/[ ] buttons to select Small, Large, or None. Note: · If the Front setting in step 4 is set to Small, the Large option cannot be selected. 7 Press the [SETUP] button. Setup closes. TESTING THE SPEAKERS To test that all of the speakers are working properly, press the remote controller's [TEST TONE] button. The test tone will be output by each speaker in turn and the name of each speaker will appear on the display. · If the test tone is not produced by a speaker, or it's produced by a speaker other than that shown on the display, you may have wired the speakers incorrectly and you should check your connections (see page 17). · If the test tone is not produced by a speaker and its name does not appear on the display, you may have set the speaker settings incorrectly (see page 32). 33 Playing Your AV Components Basic AV Receiver Operation 2 STANDBY/ON DISPLAY TUNING / PRESET 4 1 MASTER VOLUME ENTER ON STANDBY REMOTE MODE RECEIVER TAPE/AMP DVD 1 INPUT SELECTOR 1 V1 2 V2 3 V3 CD 4 7 TAPE TONE + STEREO LISTENING MODE DISPLAY DIGITAL INPUT RT/PTY/TP MEMORY TUNING MODE RETURN SETUP 5 MULTI CH 6 DVD MD STANDBY 8 TUNER 9 CD CDR A SPEAKERS B +10 --/--CD 0 DIMMER CLR SLEEP CLEAR PHONES MULTl CH DVD VIDEO 1/VCR VIDEO 2 VIDEO 3 TAPE TUNER DISC CH VOL 4 MULTI CH 1 2 TOP MENU MENU SP A / B MUTING ENTER 1 AV receiver DVD VIDEO 1/VCR VIDEO 2 Remote controller Use the AV receiver's input selector buttons to select the input source. To select the input source with the remote controller, press the [RECEIVER] button, and then use the INPUT SELECTOR buttons. On the remote controller, the [V1], [V2], and [V3] buttons select the VIDEO 1/VCR, VIDEO 2, and VIDEO 3 input sources respectively. VIDEO 3 TAPE TUNER CD 2 AV receiver A SPEAKERS B Remote controller Use the SPEAKERS [A] and [B] buttons on the AV receiver or the [SP A/B] button on the remote controller to select the speaker set that you want to use. Pressing the remote controller's [SP A/B] button cycles through the following settings: Speaker Set A Speaker Set A&B Speaker Set B Off. The MEMORY indicator appears and the preset number flashes. Select the preset that you want to delete. While holding down the [MEMORY] button, press the [TUNING MODE] button. The selected preset is deleted and its number disappears from the display. 3 TUNING / PRESET ENTER While the MEMORY indicator is displayed (about 8 seconds), use the PRESET [ ]/[ ] buttons to select a preset from 1 through 30. In this example, preset #3 is selected. Displaying Radio Information 1 TUNING / PRESET MASTER VOLUME STANDBY/ON ENTER STANDBY A SPEAKERS B TONE + STEREO LISTENING MODE DISPLAY DIGITAL INPUT RT/PTY/TP MEMORY TUNING MODE RETURN SETUP CLEAR PHONES MULTl CH DVD VIDEO 1/VCR VIDEO 2 VIDEO 3 TAPE TUNER CD 4 MEMORY Press the [MEMORY] button again to store the station. Repeat this procedure for all your favorite radio stations. 1 DISPLAY Press the [DISPLAY] button repeatedly to cycle through the available information. Selecting Preset Stations Band, preset # & frequency 1 TUNING / PRESET MASTER VOLUME Listening mode STANDBY/ON ENTER STANDBY A SPEAKERS B TONE + STEREO LISTENING MODE DISPLAY DIGITAL INPUT RT/PTY/TP MEMORY TUNING MODE RETURN SETUP CLEAR PHONES MULTl CH DVD VIDEO 1/VCR VIDEO 2 VIDEO 3 TAPE TUNER CD 1 TUNING / PRESET ENTER Use the PRESET [ ]/[ ] buttons, or the remote controller's CH [+/­] button to select a preset. 37 Using the Tuner--Continued Using RDS (European models only) RDS only works with European models and only in areas where RDS broadcasts are available. When tuned into an RDS station, the RDS indicator appears. RDS indicator Program Types Used in Europe (PTY) Type None News reports Current affairs Display NONE NEWS AFFAIRS Description No program type. Topical reporting of current affairs, often with a wider range of topics than news reports. General information such as weather forecasts, consumer affairs, medical help, etc. RDS stands for Radio Data System and is a method of transmitting data in FM radio signals. It was developed by the European Broadcasting Union (EBU) and is available in most European countries. In addition to displaying text information, RDS can also help you find radio stations by type (e. g. , news, sport, rock, etc. ). [. . . ] This is to prevent noise when you use the pause, fast forward, or fast reverse function on your player. If you switch your player from DTS to PCM, because the AV receiver does not switch formats immediately, you may not hear any sound, in which case you should stop your player for about three seconds, and then resume playback. · With some CD players, you won't be able to playback DTS material properly even though your player is connected to a digital input on the AV receiver. This is usually because the DTS bitstream has been processed (e. g. , output level, sampling rate, or frequency response changed) and the AV receiver doesn't recognize it as a genuine DTS signal. [. . . ]