User manual ONKYO TX-SV313

[. . . ] 57 En WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Important Safety Instructions 1. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. [. . . ] The crossover frequency can be Cone diameter changed on page 50. 5 1 RECEIVER Press the [RECEIVER] button, followed by the [SETUP] button. Use the Down [ ] button to select "Center, " and then use the Left and Right [ ]/[ ] buttons to select Small, Large, or None. Note: · If the Front setting in step 4 is set to Small, the Large option cannot be selected. SETUP 35 First Time Setup--Continued 6 Use the Down [ ] button to select "Surround, " and then use the Left and Right [ ]/[ ] buttons to select Small, Large, or None. Note: · If the Front setting in step 4 is set to Small, the Large option cannot be selected. Testing the Speakers To test that all of the speakers are working properly, press the remote controller's [TEST TONE] button. LISTENING MODE STEREO SURROUND AUDIO SUBTITLE RANDOM REPEAT TEST TONE TEST TONE CH SEL PLAY MODE LEVEL- LEVEL+ DISPLAY VCR L NIGHT DVD CINE FLTR HDD RC-647M 7 Use the Down [ ] button to select "Surr Back, " and use the Left and Right [ ]/[ ] buttons to select Small, Large, or None. Notes: · If the Surround setting in step 6 is set to None, this setting does not appear. · If the Surround setting in step 6 is set to Small, the Large option cannot be selected. Use the Down [ ] button to select "Surr Back Ch, " and use the Left and Right [ ]/[ ] buttons to select 2ch or 1ch. 2ch: Select if two (left and right) surround back speakers are connected. Note: · If the Surround and Surr Back settings in steps 6 and 7 are set to None, this setting does not appear. The test tone will be output by each speaker in turn and the name of each speaker will appear on the display. · If the test tone is not produced by a speaker, or it's produced by a speaker other than that shown on the display, you may have wired the speakers incorrectly and you should check your connections (see page 17). · If the test tone is not produced by a speaker and its name does not appear on the display, you may have set the speaker configuration incorrectly (see page 35). · Testing cannot be performed while speaker set B is on or a pair of headphones is connected. 8 9 SETUP Press the [SETUP] button. Press the buttons repeatedly to change the frequency one step at a time. 1 Press the [SETUP] button, use the Up and Down [ ]/[ ] buttons to select "0. Use the Up and Down [ ]/[ ] buttons to select "AM Freq, " and then use the Left and Right [ ]/[ ] buttons to select: 10 kHz: Select if 10 kHz steps are used in your area. Setup closes. 2 The American model changes FM frequency in 0. 2 MHz steps, 10 kHz steps for AM. For other models it's 0. 05 MHz steps for FM and 9 kHz (or 10 kHz) steps for AM. When tuned into a stereo FM station, the FM STEREO indicator also appears. TUNED AUTO FM STEREO 3 Tuning into Weak FM Stereo Stations If the signal from a stereo FM station is weak, it may be impossible to get good reception. In this case, switch to Manual Tuning mode and listen to the station in mono. Note: · You can also use the remote controller's Up and Down [ ]/[ ] buttons to tune the radio. 39 Listening to the Radio--Continued Tuning into Stations by Frequency You can tune into AM and FM stations directly by entering the appropriate frequency. ON/STANDBY REMOTE MODE 2 MEMORY Press the [MEMORY] button. The MEMORY indicator appears and the preset number flashes. RECEIVER TAPE DVD M D/CDR RECEIVER INPUT SELECTOR Number buttons D TUN 1 V1 2 V2 3 V3 CD HDD 4 7 TAPE 5 MULTI CH 6 DVD TV 3 CH +/­ TUNING PRESET 8 TUNER 9 CD VCR 12 CABLE 10 11 +10 D TUN 0 ENT DIMMER CLR SLEEP SAT --/--- While the MEMORY indicator is displayed (about 8 seconds), use the PRESET [ ]/[ ] buttons to select a preset from 1 through 40. ENTER TV INPUT GUIDE TOP MENU VOL DISC ALBUM CH VOL PREVIOUS MENU SP A / B MUTING ENTER PLAYLIST/CAT PLAYLIST/CAT 4 MEMORY RETURN SETUP 1 RECEIVER Press the [RECEIVER] button, followed by the [D TUN] button. Press the [MEMORY] button again to store the station. Repeat this procedure for all of your favorite AM/FM radio stations. Selecting Presets D TUN (Actual display depends on country. ) The [RECEIVER] button flashes. Within 8 seconds, use the number buttons to enter the frequency of the radio station. Note: While the [RECEIVER] button is flashing, the input source cannot be changed by using the remote controller. 1 TUNING PRESET 2 ENTER To select a preset, use the PRESET [ ]/[ ] buttons, or the remote controller's CH [+/­] button. DISC ALBUM CH Deleting Presets 1 Presetting Radio Stations PRESET MASTER VOLUME TUNING PRESET Select the preset that you want to delete. [. . . ] Before disconnecting the power cord from the wall outlet, set the AV receiver to Standby. Memory Backup The AV receiver uses a battery-less memory backup system in order to retain radio presets and other settings when it's unplugged or in the case of a power failure. Although no batteries are required, the AV receiver must be plugged into an AC outlet in order to charge the backup system. Once it has been charged, the AV receiver will retain the settings for several weeks, although this depends on the environment and will be shorter in humid climates. The following settings can be made for the S-Video and composite video inputs You must use the buttons on the unit to make these settings. [. . . ]