User manual ONKYO TX-SV313PRO

[. . . ] 90 En WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Important Safety Instructions 1. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. [. . . ] If the input signal is not PCM, the PCM indicator will flash and there will be no sound. If the input signal is not DTS, the DTS indicator will flash and there will be no sound. If no digital input signal is present, the corresponding analog input is used instead. 48 Listening to the Radio AM Frequency Step Setup (on some models) 2 Use the Up and Down [ ]/[ ] buttons to select "0. HardwareSetup, " and then press [ENTER]. 1 2, 3 1, 5 2­4 3 Use the Up and Down [ ]/[ ] buttons to select "AM Freq. " 4 Use the Left and Right [ ]/[ ] buttons to select: 10kHz: Select if 10kHz steps are used in your area. 9kHz: Select if 9kHz steps are used in your area. For AM tuning to work properly, you must specify the AM frequency step used in your area. Note that when this setting is changed, all radio presets are deleted. To change the frequency step on the TX-SV313PRO, follow the procedure below. 5 Press the [SETUP] button. Setup closes. 1 Press the [RECEIVER] button, followed by the [SETUP] button. Note: · This procedure can also be performed on the AV receiver by using its [SETUP], [ENTER], and arrow buttons. 49 Listening to the Radio--Continued Listening to AM/FM Stations TUNER STANDBY/ON TUNING Manual Tuning Mode TUNING MASTER VOLUME PRESET 1 TUNING MODE Press the [TUNING MODE] button so that the AUTO indicator disappears from the display. STANDBY ZONE 2 ENTER PURE AUDIO PURE AUDIO MULTI CH DVD VCR/DVR CBL/SAT AUX TAPE TUNER CD SETUP RETURN AUX INPUT PHONES SETUP MIC VIDEO L AUDIO R ZONE 2 OFF TONE MOVIE/TV MUSIC GAME DISPLAY DIGITAL INPUT RT/PTY/TP MEMORY TUNING MODE CLEAR 2 TUNING TUNING MODE With the built-in tuner, you can enjoy AM and FM radio stations and store your favorite stations as presets for easy selection. In this example, FM has been selected. Band Frequency Press and hold the TUNING Up or Down [ ]/[ ] button. Press the button repeatedly to change the frequency one step at a time. TUNER The North American model changes FM frequency in 0. 2MHz steps, 10kHz steps for AM. For other models it's 0. 05MHz steps for FM and 9kHz (or 10kHz) steps for AM. Tuning into Weak FM Stereo Stations If the signal from a stereo FM station is weak, it may be impossible to get good reception. The RT information scrolls across the display. Listening to Traffic News (TP) 1 STANDBY/ON STANDBY ZONE 2 PURE AUDIO 3 MASTER VOLUME TUNING PRESET ENTER Notes: · The message "Waiting" may appear while the AV receiver waits for the RT information. · If the message "No Text Data" appears on the display, no RT information is available. PURE AUDIO MULTI CH DVD VCR/DVR CBL/SAT AUX TAPE TUNER CD SETUP RETURN AUX INPUT PHONES SETUP MIC VIDEO L AUDIO R ZONE 2 OFF TONE MOVIE/TV MUSIC GAME DISPLAY DIGITAL INPUT RT/PTY/TP MEMORY TUNING MODE CLEAR Finding Stations by Type (PTY) 2 You can search for stations that broadcast traffic news. MASTER VOLUME 1 STANDBY/ON STANDBY ZONE 2 PURE AUDIO 4, 5 TUNING PRESET ENTER 1 TUNER Use the [TUNER] input selector button to select FM. PURE AUDIO MULTI CH DVD VCR/DVR CBL/SAT AUX TAPE TUNER CD SETUP RETURN AUX INPUT PHONES SETUP MIC VIDEO L AUDIO R ZONE 2 OFF TONE MOVIE/TV MUSIC GAME DISPLAY DIGITAL INPUT RT/PTY/TP MEMORY TUNING MODE CLEAR 2 23 You can search for radio stations by type. RT/PTY/TP 1 TUNER Use the [TUNER] input selector button to select FM. Press the [RT/PTY/TP] button three times. If the current radio station is broadcasting TP (Traffic Program), "[TP]" will appear on the display and traffic news will be heard as and when it's broadcast. If "TP" without square brackets appears, this means that the station is not broadcasting TP. The AV receiver searches until it finds a station that's broadcasting TP. If no stations are found, the message "Not Found" appears. 2 RT/PTY/TP Press the [RT/PTY/TP] button twice. Use the PRESET [ ]/[ ] buttons to select the type of program you want. See the table on page 53. 3 ENTER 3 PRESET 54 Using the Listening Modes Selecting the Listening Modes For a description of each listening mode, see "About the Listening Modes" on page 59. · The Dolby Digital and DTS listening modes can only be selected if your DVD player is connected to the AV receiver with a digital audio connection (coaxial, optical, or HDMI). · The listening modes you can select depends on the format of the input signal. To check the format, see "Displaying Source Information" on page 47. · While a pair of headphones is connected, you can only select the Pure Audio, Mono, Direct, or Stereo listening mode. Selecting with the Remote Controller MOVIE/TV MUSIC STEREO GAME Selecting on the AV Receiver MUSIC MASTER VOLUME [MOVIE/TV] button This button selects the listening modes intended for use with movies and TV. TUNING PRESET STANDBY/ON STANDBY ZONE 2 ENTER PURE AUDIO [MUSIC] button This button selects the listening modes intended for use with music. [. . . ] Select another listening mode. Tuner Reception is noisy, stereo FM reception suffers from hiss, or the FM STEREO indicator doesn't light up · Relocate your antenna. · When listening to an AM station, operating the remote controller may cause noise. · If nothing improves the reception, install an outdoor antenna. Others The sound changes when I connect my headphones · When a pair of headphones is connected, the listening mode is set to Stereo, unless it's already set to Stereo, Mono, Direct, or Pure Audio, in which case it stays the same. How do I change the language of a multiplex source · On the "Audio Adjust" menu, change the "Input (Mux)" setting to Main or Sub (page 63). [. . . ]