User manual ONKYO TX-SV414PRO

[. . . ] Use the 8-pin mini DIN connector cable to connect the SiriusConnect receiver to the SIRIUS jack on the rear of the AV receiver. Indoor/outdoor antenna with 21-foot cable SiriusConnect receiver 8-pin mini DIN connector cable SIRIUS jack AC power To use the included antenna indoors, you must place it at a north-, west-, or east-facing window, depending on where you live. If this isn't possible, you'll need to install it outside, away from any overhead obstructions. En Positioning the Antenna For a consistent satellite signal, the antenna must be positioned correctly. Use the following map to determine which area you are in and position the antenna accordingly. SKY NORTH Setting the Satellite Radio Mode Before you can listen to SIRIUS Satellite Radio, you must set the SAT Radio Mode to "SIRIUS". 1 Press the [RECEIVER] button, followed by the [SETUP] button. The main menu appears onscreen. WEST 1 5 4 EAST 2 3 HORIZON SOUTH 2 Area 1: Point the antenna toward the sky in the east, northeast, or southeast, either through a window or outside. [. . . ] Area 3: Point the antenna toward the sky in the north or northwest, either through a window or outside. Area 4: Point the antenna toward the sky in the west, northwest, or southwest, either through a window or outside. The antenna cannot be used indoors. Use the Up and Down [ ]/[ ] buttons to select "7. Tuner FM/AM Frequency Step SAT Radio Mode 200kHz/10kHz None RECEIVER SETUP 4 TUNER TUNING / Use the Left and Right [ ]/[ ] buttons to select "SIRIUS". If there are 2 items on the Tuner screen, use Up and Down [ ]/[ ] buttons to select "SAT Radio Mode". Pressing the Left and Right [ ]/[ ] buttons cycles through the following options: None SIRIUS None: Select if you're not using Satellite Radio. SIRIUS: Select to use SIRIUS Satellite Radio. 2 5 When you've finished, press the [SETUP] button. Setup closes. Selecting SIRIUS Satellite Radio Channels There are three ways to select SIRIUS Satellite Radio channels: 1. Direct tuning: enter channel number. Remote indicator Selecting SIRIUS Satellite Radio AV receiver On the AV receiver, press the [TUNER] button repeatedly to select "SIRIUS". On the remote controller, press the [RECEIVER] REMOTE MODE button, and then press the [TUNER] INPUT SELECTOR button repeatedly to select SIRIUS. If "CHECK SR TUNER" appears on the display, make sure the SiriusConnect receiver is connected properly. Note: The SIRIUS Parental Lock cannot be set unless the AV receiver and the SiriusConnect receiver are connected. 3 Use the Up and Down [ ]/[ ] buttons to select "2. Tuner FM/AM Frequency Step SAT Radio Mode Antenna Aiming SURIUS Parental Lock 200kHz/10kHz SIRIUS -> -> 6 Use the Up and Down [ ]/[ ] buttons to select "Parental Lock", and then press [ENTER]. The Parental Lock screen appears. 6 7 Use the Up and Down [ ]/[ ] buttons to select a channel, and use the Left and Right [ ]/[ ] buttons to select Locked or Unlocked. The number, name, and status of the currently selected channel is displayed. When you've finished, press [ENTER] to save your changes, or press [RETURN] to return to the previous screen without saving. When [ENTER] is pressed, the confirmation message "Locked" or "Unlocked" appears. Setup closes. 3 Use the Up and Down [ ]/[ ] buttons to select "2. Tuner FM/AM Frequency Step SAT Radio Mode Antenna Aiming SURIUS Parental Lock 200kHz/10kHz SIRIUS -> -> 8 4 Use the Up and Down [ ]/[ ] buttons to select "SIRIUS Parental Lock", and then press [ENTER]. The SIRIUS Parental Lock screen appears. SIRIUS Parental Lock Enter Code 9 0 1 2 3 4 5 6 7 8 9 Notes: · While a channel is locked, it cannot be selected for listening. · To unlock a channel, you must enter the correct PIN number and change it to Unlocked in step 6. Note: If the SAT Radio Mode is set to "None" (see page 2), the "SIRIUS Parental Lock" item is not available. Changing the PIN Number 1 Press the [RECEIVER] button, followed by the [SETUP] button. The main menu appears onscreen. 5 Use the Left and Right [ ]/[ ] buttons to select a number on the screen, and then press [ENTER]. [. . . ] The main menu appears onscreen. 5 Use the Left and Right [ ]/[ ] buttons to select a number on the screen, and then press [ENTER]. If you're entering the PIN number for the very first time, the PIN is stored, and the following screen appears. SIRIUS Parental Lock Edit Code Parental Lock -> 2 Use the Up and Down [ ]/[ ] buttons to select "7. HDMI If you've already set a PIN number, you must enter the correct PIN to get to this screen. If you enter the wrong PIN, the message "Wrong Code!" appears and you'll have to enter the PIN again. [. . . ]