User manual ONKYO TX-SV525

[. . . ] 16 Enjoying music or videos Enjoying music or videos with the TX-SV525 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Changing the default settings according to your connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new AV Receiver. [. . . ] Press the SPEAKER ADJUST three times. "Distance Setup" then "Front:" are displayed. To select other speakers, press SPEAKER ADJUST again. Speaker Distance 4. Repeat steps 2 and 3 for all five parameters. Speaker Distance Front (From Front-left and front-right speakers to your listening position. The default setting is 12 ft (3. 6 m). ) Center (From Center speaker to your listening position. The default setting is 12 ft (3. 6 m). ) Surr Right (From Surround-right speaker to your listening position. The default setting is 7 ft (2. 1 m). ) Surr Left (From Surround-left speaker to your listening position. The default setting is 7 ft (2. 1 m). ) Subwoofer (From Subwoofer to your listening position. The default setting is 12 ft (3. 6 m). ) 19 Speaker setup Before operating the remote controller, press RCVR/TAPE. SUBWOOFER MODE TEST CH SEL LEVEL Setting the subwoofer mode Press SUBWOOFER MODE on the unit. With the first press of the button, you can check the present setting. Then each press of the button changes the subwoofer mode as follows (a tip on how to select the right subwoofer mode is in parenthesis): Adjusting each speaker's relative volume balance -- Test tone Adjust each speaker's relative volume balance so that the volumes of all speakers' test tones sound equal at the listening position. Adjust the volume to your normal listening level, prior to commencing settings. Note You cannot adjust the volume balance while the muting function is activated. Subwoofer Mode 1 (Default) (To output the low frequencies of all channels from the subwoofer. ) 1. After you release the button and a station is received in stereo, the scanning stops. 22 Listening to the radio PRESET FM MODE MEMORY Before operating the remote controller, press RCVR/TAPE. TUNER PRESET/ADJUST TUNER Presetting radio stations You can preset up to 30 stations. Selecting preset stations Before selecting preset stations, you need to preset the radio stations. See "Presetting radio stations" on the left column of this page. 1. Tune in the radio station you wish to preset (refer to the previous page). Press MEMORY. The MEMORY indicator lights and the preset number starts flashing in the display. 1. Press TUNER to switch the input source to the tuner. "FM" or "AM" appears in the display. While the MEMORY indicator is lit (for about 8 seconds), press PRESET/ADJUST / to select the preset number. 2. Press PRESET / on the remote controller or PRESET/ADJUST / on the unit repeatedly to select the preset number of the desired radio station. 4. To register another preset station, repeat steps 1 to 4. Erasing a preset station 1. Press FM MODE while holding down MEMORY. The selected preset channel will be erased. 23 Various functions common to all the sources SPEAKERS A/B SP A/SP B Before operating the remote controller, press RCVR/TAPE. MUTING PHONES jack Turning on/off the speaker system A/B You can turn on or off the speaker systems connected to the speaker system A and speaker system B connectors individually. Before operating the remote controller, press RCVR/TAPE. Muting the sound (remote controller only) Press MUTING. The MUTING indicator flashes in the display during the muting mode. Press SPEAKER A on the unit or SP A on the remote controller to turn on or off the speaker system A. Press SPEAKER B on the unit or SP B on the remote controller to turn on or off the speaker system B. Note If you turn on the speaker system B, the speaker system A also reproduces stereo sound automatically. [. . . ] No picture appears on the TV screen. · The placement of the audio connection cables on the rear panel is incorrect. · The TV is not set to receive the output signals from the AV receiver. · Only the S video connection is made. The sound of the playback source is not heard. · Another input source is selected. · The remote controller is not pointed at the remote sensor of the AV receiver. [. . . ]