User manual ONKYO TX-SV636

[. . . ] REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. Important Safety Instructions 1. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. [. . . ] Here you can specify the distance from each speaker to the listening position so that the sound from each speaker arrives at the listener's ears as the sound designer intended. +10 0 MACRO 1 2 3 ZONE2 3 ENTER CLEAR 12 11 --/--- 10 INPUT SELECTOR 1 2 REMOTE MODE RECEIVER TAPE/AMP TV VCR CABLE CDR SAT MD DVD CD HDD Use the Up and Down [ ]/[ ] buttons to select "a. Unit, " and then use the Left and Right [ ]/ [ ] buttons to select: feet: Select if you want to enter distances in feet. Front, " and then use the Left and Right [ ]/ [ ] buttons to specify the distance. Specify the distance from the front left speaker to your listening position. DIMMER P TO MEN U SLEEP MEN U 4 2­5 1, 6 ENTER + CH DISC ALBUM ENTER VOL PREV CH DISPLAY RE TUR N SET UP MUTING REC PLAYLIST RANDOM 5 6 Repeat step 4 for all speakers. The setup menu closes. 1 RECEIVER Press the [RECEIVER] button followed by the [SETUP] button. The main menu appears onscreen. 2 ENTER Use the Up and Down [ ]/[ ] buttons to select "2. The Speaker Distance menu appears. ENTER Notes: · The Center and Subwoofer distances can be set up to 5 ft. (6 m), the Center and Subwoofer distances can be set between 15 and 25 ft. The Surr Right, Surr Left, and Surr Back distances can be set up to 5 ft. (6 m), the Surr Right, Surr Left, and Surr Back distances can be set between 5 and 25 ft. · This procedure can also be performed on the AV receiver by using its [SETUP] button, arrow buttons, and [ENTER] button. Note: Speakers that you set to No or None on the Speaker Configuration page (page 44) cannot be selected. 47 TXSR603X. book 48 y·[W , Q, O, O, T"N, WOEZ, R"ú·@·. . . --j"ú·@OEßOEã, QZz, Q·ª First Time Setup--Continued Speaker Level Calibration This setting is set automatically by the Automatic Speaker Setup function (see page 38). When you select DVD or another video component, on your TV, you'll need to select the video input that's connected to the AV receiver's MONITOR OUT. On some DVD players, you may need to turn on the digital audio output. Remote controller 3 AV receiver MASTER VOLUME or VOL To adjust the volume, use the MASTER VOLUME control, or the remote controller's [VOL] button. It has a wide volume range, allowing precise adjustment. 51 TXSR603X. book 52 y·[W , Q, O, O, T"N, WOEZ, R"ú·@·. . . --j"ú·@OEßOEã, QZz, Q·ª Basic Operations--Continued 4 CD 5 TAPE 6 TUNER - Using the Sleep Timer With the sleep timer, you can set the AV receiver to turn off automatically after a specified period. Press the [RECEIVER] button, and then press the [SLEEP] button repeatedly to select the required sleep time. The SLEEP indicator appears on the display when the sleep timer has been set. The specified sleep time appears on the display for about five seconds, then the previous display reappears. If you need to cancel the sleep timer, press the [SLEEP] button repeatedly until the SLEEP indicator disappears. To check the time remaining until the AV receiver sleeps, press the [SLEEP] button. Note that if you press the [SLEEP] button while the sleep time is being displayed, you'll shorten the sleep time by 10 minutes. 7 +10 8 0 MACRO 9 T V VOL CLEAR 12 11 - - / - - - 10 INPUT SELECTOR Press [RECEIVER] first DIMMER 1 2 3 ZONE2 REMOTE MODE RECEIVER TAPE/AMP TV VCR CABLE CDR SAT MD DVD CD HDD RECEIVER SLEEP TO EN PM U DIMMER MEN U SLEEP SLEEP VOL + CH DISC ALBUM ENTER PREV CH DISPLAY RE TU R N SE T UP MUTING MUTING REC PLAYLIST RANDOM Setting the Display Brightness You can adjust the brightness of the display. RECEIVER DIMMER Press the [RECEIVER] button, and then press the [DIMMER] button repeatedly to select: · Normal+VOLUME light on. · Dimmer+VOLUME light off. Using Headphones You can connect a pair of stereo headphones (1/4-inch phone plug) to the AV receiver's PHONES jack for private listening, as shown. STANDBY/ON Muting the AV Receiver You can temporarily mute the output of the AV receiver. The output is muted and the MUTING indicator flashes on the display, as shown. PHONES STANDBY ZONE2 OFF ZONE 2 LEVEL TONE + STEREO LIS PHONES MULTl CH DVD VIDEO 1 V VCR 1 V RECEIVER MUTING To unmute the AV receiver, press the [MUTING] button again, or adjust the volume. [. . . ] · Make sure that the AV receiver is not subjected to direct sunshine or inverter-type fluorescent lights. · If the AV receiver is installed in a rack or cabinet with colored-glass doors, the remote controller may not work reliably when the doors are closed. · Make sure you've selected the correct remote controller mode (pages 14-18). · When using the remote controller to control other manufacturers' AV components, some buttons may not work as expected. [. . . ]