User manual OREGON THGN810

[. . . ] · Consult the dealer or an experienced radio / TV technician for help. Wireless Remote Sensor with LCD display Model: THGR810 Wireless Remote Sensor Model: THGN810 USER MANUAL For best results: · Place the sensor out of direct sunlight and moisture. · Do not place the sensor more than 100 m (330 ft) from the main (indoor) unit. · Position the sensor so that it faces the main (indoor) unit, minimizing obstructions such as doors, walls, and furniture. [. . . ] Please call our customer service number (listed on our website at www. oregonscientific. com), or on the warranty card for this product) for all inquiries instead. 19861 SW 95th Ave. , Tualatin, Oregon 97062 USA 1-800-853-8883 THGR810 / THGN810 Remote Sensor IDT Technology Limited Block C, 9/F, Kaiser Estate, Phase 1, 41 Man Yue St. , Hung Hom, Kowloon, Hong Kong is in conformity with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation. declare that the product Product Name: Manufacturer: Address: EN INTRODUCTION Thank you for selecting the Oregon ScientificTM remote thermohygro sensor (THGR810 / THGN810). It contains practical step-by-step instructions, as well as technical specifications and warnings you should know about. SPECIFICATIONS LxWxH Weight Humidity range Humidity resolution Temp. Batteries 92 x 60 x 20 mm (3. 6 x 2. 4 x 0. 79 in) 62 g (2. 22 oz) 5% to 95% 1% ºC (ºF) -30ºC (-22ºF) to 60ºC (140ºF) 0. 1ºC (0. 2ºF) 433 MHz 100 meters (330 feet) Every 60 seconds 1 - 10 2 x UM-4 (AAA) 1. 5V PRODUCT OVERVIEW 1 2 SET CHANNEL 1. LCD display (the THGN810 does not have an LCD screen) : Shows the channel number, temperature and humidity readings, and comfort level 2. LED status indicator Set the channel by adjusting the CODE switch to one of the following settings. Battery compartment 6 7 8 9 10 10 Other switch settings (Not recommend) SWITCH SETTING EU-DECLARATION OF CONFORMITY Hereby, Oregon Scientific, declares that this Remote Sensor (Model THGR810 / THGN810) is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. A copy of the signed and dated Declaration of Conformity is available on request via our Oregon Scientific Customer Service. 1 2 3 4 ABOUT OREGON SCIENTIFIC Visit our website (www. oregonscientific. com) to learn more about Oregon Scientific products such as digital cameras; MP3 players; children's electronic learning products and games; projection clocks; health and fitness gear; weather stations; and digital and conference phones. The website also includes contact information for our Customer Care department in case you need to reach us, as well as frequently asked questions and customer downloads. We hope you will find all the information you need on our website, however if you're in the US and would like to contact the Oregon Scientific Customer Care department directly, please visit: www2. oregonscientific. com/service/default. asp OR Call 1-800-853-8883. For international inquiries, please visit: www2. oregonscientific. com/about/international. asp GETTING STARTED BATTERIES Insert batteries before first use, matching the polarity (+ and -) as shown in the battery compartment. For best results, install batteries in the remote sensor before the main unit. Press RESET after each battery change. COUNTRIES RTTE APPROVAL COMPLIED All EU Countries, Switzerland CH and Norway N NOTE It is recommended that you use alkaline batteries with this product for longer performance and consumer grade lithium batteries in below freezing temperatures (0ºC / 32ºF). [. . . ] Collection of such waste separately for special treatment is necessary. NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ]