User manual PALSONIC MODEL 3425G

[. . . ] OWNER'S MANUAL 34CM CORDLESS REMOTE COLOUR TELEVISION MODEL: 3425G Type Tested Electrical Safety AS/NZS 3250 Lic 4163 Standards Australia APP No: N15957 PALSONIC CORPORATION PTY LTD 1 JOYNTON AVENUE WATERLOO NSW 2017 AUSTRALIA TEL:(02)9313 7111 FAX:(02)9313 7555 www. palsonic. com. au PALSONIC CUSTOMER SERVICE TELEPHONE AUSTRALIA:1300 657 888 Contents Contents Congratulations on your purchase of this Palsonic colour television receiver. We recommend that you thoroughly read this manual before use to fully enjoy the many functions and excellent effects of this receiver. Retain this manual in an easily accessible location for future reference. Note: Screen displays and illustrations in this manual may differ from the actual ones for better visibility. CONTENTS 1 2 4 4 5 6 7 7 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The aerial cable should not be bundled with the power cord and the like. 8 Connect to video and audio equipment This TV set provides AV input terminals for your convenient connection to VTR, DVD or video camera to enjoy the high quality picture. Please refer to the owner's manual of the equipment to be connected as well. Important notes on the AV input terminals Please do not connect and use the front and rear input terminals at the same time. You can also use the AV terminals on the TV set rear as follows. 9 Operations Turning on/off Turning on/off Turning on 1 2 3 ! Press the Power Switch on the TV set. If no picture appears, then the TV set is in STANDBY mode. Now please follow step 2. In STANDBY mode, press the button on the remote controller and the TV set is turned on. In STANDBY mode, you can also press the AV/TV button on the set to turn on. Notes: If there is no input signal, then a blueback appears. After 15 minutes, the set auto goes to STANDBY. Turning off the Power Switch on the 1 Press off the power completely. TV set if you want to cut 2 If you want to turn off the TV set temporarily, press the button on the remote controller. 10 Operations Select Input Signal Select input signal Select input signal 1 Press AV/TV button on the TV set or AV button on the remote control. When the set is in TV mode, press this button and the set goes to AV mode. If you want to switch to TV press AV button again or follow step 2, 3 or 4. 2 Press digit buttons to switch back to TV mode. 4 Press 5 button to switch back to TV mode. Press DSP button, the set displays current input mode. The OSD disappears in about 5 seconds. 18:09 19 !Notes: If the Timer item has been set, the current time also appears. 11 Operations 1 2 3 Press MENU button four times to call Program menu page. Press VOL+ or VOL- buttons to adjust item. Tuning in Auto search/Manual search/Channel skip/Fine tuning Auto Search 1 2 3 ! Press MENU button repeatedly to enter into Program menu page. Press VOL+ button to start Auto Search towards higher frequency; or press VOL- button to start Auto Search towards lower frequency. All active channels will be preset and stored into the memory automatically. After presetting, the TV will stop at the last channel program. Notes: 1. Before you start Auto Search, we strongly recommend you to set a proper Sound System according to your local area. During the process of AUTO SEARCH, pressing the MENU or CH+/- buttons will stop the process. Manual Search Use MANUAL SEARCH function if desired channels cannot be preset or if you would like to preset channels to specific position numbers one by one. 1 2 3 4 5 ! Notes: Press MENU button repeatedly to enter into Program menu page. Press VOL+ or VOL- button to select a channel number (ranging from 0-254). Press VOL+ or VOL-button to start program search manually. Pressing VOL+ the set searches towards higher frequency; Pressing VOL-, the set searches towards lower frequency; The search stops when a program found and this program will be stored in the specified position number. 1. Then you can select a proper sound system as follows. 1 2 3 Press MENU button repeatedly to enter into Program menu page. Press VOL+ or VOLbutton to select a proper sound system. Some models are with only one sound system and in this case the Sound System does not need to be adjusted. !Notes: When the set is in AV mode, only Colour System appears in Program menu page. Program Color System AUTO 14 Operations Channel Selection Channel Selection 1 Use Direct Channel Selector (0-9 and -/-- buttons) To select one-digit channel: Press -/-- button repeatedly to display "-". Press 0-9 direct channel selector. 8 To select two-digit channel: Press -/-- button repeatedly to display "--". -- Press 1-9 buttons. -1 Press 0-9 buttons. 18 To select three-digit channel: Press -/-- button repeatedly to display "--" --- -- 1 -16 168 Press 1-2 buttons. Press 0-9 buttons. Press 0-9 buttons. ! Notes: The maximum channel number is 254, the set does not act if the channel number you input is out of the range of 0~254. 2 3 Use CH+ or CH- button Press CH+ button, the channel number increases; Press CH- button, the channel number decreases. Use previous channel button Press this button to switch between the current channel and previous channel. 15 Operations Adjusting Picture Contrast/Colour/Brightness/Sharpness/Picture Mode Adjusting Picture 1 Press MENU button, the Picture menu page displays. 3 Press VOL+ or VOL- button to adjust. Item Contrast Color Brightness Sharpness Tint* VOLweaker paler darker softer purplish VOL+ stronger deeper lighter sharper greenish * Note: The item TINT is for NTSC only. Press the | button to select a picture mode according to your favourites. 4 Press | Item button to select picture mode. [. . . ] If there are two continual boxes, you can not push them. 21 Operations Teletext function, therefore only a set with the teletext system can receive the teletext Teletext is an optional broadcast. Switch on/off/Description of TELETEXT/Button Introduction Switching Teletext on/off Press the TEXT button to switch on teletext. To switch off teletext, press the TEXT button repeatedly until the Teletext disappears. Description of Teletext Teletext is a free service broadcast by most TV stations which gives up-to-the-minute information on news, weather, television programs, share prices and many other topics. It is the nature of the system itself, where a large amount of information is sent using a small fraction of the TV signal. If you get yourself into trouble, read the following instruction carefully. [. . . ]