User manual PALSONIC MODEL 5138HT

[. . . ] OWNER'S MANUAL 51CM CORDLESS REMOTE COLOUR TELEVISION MODEL: 5138HT Type Tested Electrical Safety AS/NZS 3250 Lic 4164 Standards Australia APP No: N15959 PALSONIC CORPORATION PTY LTD 1 JOYNTON AVENUE WATERLOO NSW 2017 AUSTRALIA TEL: (02) 9313 7111 FAX: (02) 9313 7555 www. palsonic. com. au PALSONIC CUSTOMER SERVICE TELEPHONE AUSTRALIA: 1300 657 888 Congratulations on your purchase of this Palsonic colour television receiver. We recommend that you thoroughly read this manual before use to fully enjoy the many functions and excellent effects of this receiver. Retain this manual in an easily accessible location for future reference. Screen displays and illustrations in this manual may differ from the actual ones for better visibility. Contents Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Use the remote control within the effective range as the above figure. If the remote control does not work, please check whether the batteries are exhausted or the polarity is wrong. When direct sunlight, and incandescent lamp, fluorescent lamp or any other strong light shines on the remote sensor of the TV, the remote operation may be unstable. 7 Installation Connecting antenna Optimum reception of colour requires a good signal and will generally mean that an outdoor antenna must be used. The exact type and position of the antenna will depend upon your particular area. Notes: Turn off the power first, when you connect an outdoor antenna to the antenna input terminal. When installing an outside antenna system, extreme care should be taken to keep from touching power lines or circuits as contact with them might be fatal. In thunder and lighting weather, please disconnect the outdoor antenna to avoid thunder/lightning strike. 8 Connecting video and audio equipment This TV set provides 2 groups of AV input terminals (including 1 group of DVD and S-Video input terminals) for your convenient connection to VCR, DVD or other video equipment to enjoy the high quality picture. Please refer to the owner's manual of the equipment to be connected as well. Connecting the rear AV and DVD input terminals. DVD Video equipment without S-video terminal To audio outputs R R W W To Y output To audio (R) output To audio (L) output To video output Y Y To CB output To C R output Y Yellow (video) W G B R W R white (audio L) R red (audio R, CR ) G Green (Y) B Blue (C B ) VIDEO (1) DVD Y VIDEO S-VIDEO AUDIO CB AUDIO CR Video equipment with S-video terminal R W W R To S-VIDEO output To audio outputs Notes: The S-VIDEO input terminal has priority over AV1 VIDEO terminal. If you want to use equipment connected to S-Video terminal, please disconnect any plug from DVD terminal. If you want to use equipment connect to AV1 VIDEO terminal, please disconnect any plug from DVD and S-VIDEO terminal. 9 Connecting the side AV input terminals (2) AUDIO R VIDEO EQUIPMENT Y VIDEO W To video output Y R W To audio outputs Signal Connecting the AV output terminals (1) DVD Y VIDEO VIDEO S-VIDEO AUDIO CB AUDIO CR Y Audio Amplifier 10 Operations Menu Introduction Press the MENU button repeatedly to select the screen display as below. Then arrange the preset channels with the manual search and program edit functions. Auto Search Press the MENU button to select PRESET menu. All active channels will be preset and stored into the memory automatically. During the process of Auto channel preset, pressing the MENU button will stop the process. Note: Before you start Auto Search, we recommend you to set a proper Sound system and Colour system according to your local area. PROGRAM TYPE BAND SKIP FINE TUNE MANUAL SEARCH AUTO SEARCH 008 USER2 V-H OFF SEL ADJ Manual Search If desired channel can not be preset by Auto search or if you would like to preset channels to specific position numbers one by one, use manual search function. Access the PRESET menu, then select PROGRAM item by CH+/- and set the desired channel number (from 0~199) by VOL+/- or Digit buttons. The search stops when a program is found and this program will be stored in the specified position number. PROGRAM TYPE BAND SKIP FINE TUNE MANUAL SEARCH AUTO SEARCH 008 USER2 V-H OFF SEL ADJ You can use band selection to quicken search process. Then select MANUAL SEARCH item and press VOL+/- buttons to start manual search. Repeat the above steps if you want to store another program in other position number. PROGRAM TYPE BAND SKIP FINE TUNE MANUAL SEARCH AUTO SEARCH 008 USER2 V-H OFF SEL ADJ 13 Operations Presetting programs (continued) Fine Tuning When picture and sound's effect of a channel is poor (for example: one or two CATV channel's picture and sound are not standard), you can correct them by making use of Fine tuning. Access the PRESET menu, then select PROGRAM item by CH+/- and set the desired channel number (from 0~199) by VOL+/- or Digit buttons. In the menu, select FINE TUNE item, then press and hold VOL+/- buttons until the best picture and sound are obtained. PROGRAM TYPE BAND SKIP FINE TUNE MANUAL SEARCH AUTO SEARCH 008 USER2 V-H OFF SEL ADJ 14 Operations Editing programs Channel skipping After presetting the channels, you can skip unnecessary position numbers so that only the channels you want are selected. Access the PRESET menu, then select PROGRAM item by CH+/- and set the desired channel number (from 0~199) by VOL+/- or Digit buttons. PROGRAM TYPE BAND SKIP FINE TUNE MANUAL SEARCH AUTO SEARCH 008 USER2 V-H OFF SEL ADJ In the menu, please select SKIP item and press VOL+/buttons to select ON. Now the selected channel will be skipped when you browse channels by CH+/- buttons. If the SKIP is set to ON, when you select the channel by Digit buttons, the program number displayed on the screen is purple and a " * " symbol can be seen. To restore a skipped channel, please select the skipped channel number by digit buttons. [. . . ] When one row has been filled with the cubes, the row will disappear, and your mark will gain one point. If two rows disappear at the same time, your mark will gain three points. If three rows disappear at the same time, your mark will gain seven points. The right window provides hints about next cube's shape, you can arrange current cube's position and angle in advance. [. . . ]