User manual PALSONIC MODEL 5160G

[. . . ] 12 Manual search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Skip an unnecessary channel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Fine tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Setting colour system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Do not drop, dampen or disassemble the remote control. When there is an obstacle between the TV and the transmitter, the transmitter may not operate. When direct sunlight, and incandescent lamp, fluorescent lamp or any other strong light shines on the REMOTE SENSOR of the TV the remote operation may be unstable. 7 Installation INSTALL the unit in a room where direct light will not fall upon the screen. Total darkness or a reflection on the picture screen may cause eyestrain. Soft and indirect lighting is recommended for comfortable viewing. Antenna Installation/Connect to video and audio equipment Antenna installation Optimum reception of colour requires a good signal and will generally mean that an outdoor aerial must be used. The exact type and position of the aerial will depend upon your particular area. ! Notes: It is recommended that the 75-ohm coaxial cable be used to eliminate interference and noise which may occur due to radio wave conditions. The aerial cable should not be bundled with the power cord and the like. 8 Connect to video and audio equipment This TV set provides 2 groups of AV input terminals for your convenient connection to VTR, DVD or video camera to enjoy the high quality picture. Please refer to the owner's manual of the equipment to be connected as well. Important notes on the AV input terminals Please do not connect and use the front and rear input terminals at the same time. You can also use the AV terminals on the TV set rear as follows. ! Notes: Please do not connect and use the S-VIDEO and VIDEO terminals at the same time. Please note that the rear audio input terminals are stereo while the front are mono. 9 Operations Turning on/off Turning on/off Turning on 1 2 3 ! Press the Power Switch on the TV set. If no picture appears, then the TV set is in STANDBY mode. Now please follow step 2. In STANDBY mode, press the button on the remote controller and the TV set is turned on. In STANDBY mode, you can also press the AV/TV button on the set to turn on. Notes: If there is no input signal, then a blueback appears. After 15 minutes, the set auto goes to STANDBY. Turning off the Power Switch on the 1 Press off the power completely. TV set if you want to cut 2 If you want to turn off the TV set temporarily, press the button on the remote controller. 10 Operations Select Input Signal Select input signal Select input signal 1 Press AV/TV button on the TV set or AV button on the remote control. When the set is in TV mode, press this button and the set goes to AV mode. If you want to switch to TV press AV button again or follow step 2, 3 or 4. 2 Press digit buttons to switch back to TV mode. 4 Press 5 button to switch back to TV mode. Press DSP button, the set displays current input mode. The OSD disappears in about 5 seconds. 18:09 19 !Notes: If the Timer item has been set, the current time also appears. 11 Operations 1 2 3 Press MENU button four times to call Program menu page. Press VOL+ or VOL- buttons to adjust item. Tuning in Auto search/Manual search/Channel skip/Fine tuning Auto Search 1 2 3 ! Press MENU button repeatedly to enter into Program menu page. Press VOL+ button to start Auto Search towards higher frequency; or press VOL- button to start Auto Search towards lower frequency. All active channels will be preset and stored into the memory automatically. After presetting, the TV will stop at the last channel program. Notes: 1. Before you start Auto Search, we strongly recommend you to set a proper Sound System according to your local area. During the process of AUTO SEARCH, pressing the MENU or CH+/- buttons will stop the process. Manual Search Use MANUAL SEARCH function if desired channels cannot be preset or if you would like to preset channels to specific position numbers one by one. 1 2 3 4 5 ! Notes: Press MENU button repeatedly to enter into Program menu page. Press VOL+ or VOL- button to select a channel number (ranging from 0-254). Press VOL+ or VOL- button to start program search manually. Pressing VOL+ the set searches towards higher frequency; Pressing VOL-, the set searches towards lower frequency; The search stops when a program found and this program will be stored in the specified position number. 1. [. . . ] When you push all boxes to the relevant destinations then you win and it goes to next map. If there are two continual boxes, you can not push them. 21 Others Troubleshooting Guide Trouble Shooting Before calling service personnel, please check the following chart for a possible cause to the trouble you are experiencing. Symptoms Power is not turned on Poor colour, poor tint Spots appear on the screen Stripes appear on the screen Check the following items Be sure the power cord is plugged in. Contrast, colour, tint are not correctly adjusted Possible interferences of automobiles, motorcycle, trolley bus, neon lamps, etc. Possible interference of electronic interference from another TV set, a computer, an electronics game machine, a broadcast station, etc. [. . . ]