Detailed instructions for use are in the User's Guide.
[. . . ] 22 Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hyperband English/Chinese on-screen menu display 256 preset channels Intellectualised I 2 C-bus control Full function remote control ON Timer, OFF Timer Four picture modes' setting AUDIO/VIDEO input & output terminals S-VIDEO Terminal Games, calendar function Advanced digital picture improvement circuit Digital AFT technology Channel reservation
1
NOTES FOR OPERATION
* Do not let the TV set be in stand-by condition for a long period of time. When it is not in use, please turn off the power supply and remove the power plug. When it is to be left unattended for a prolonged period of time, it is recommended to disconnect the connection to the outdoor aerial, to avoid thunder strike.
* Please follow cautions for safety in the TV set instructions, and all warnings and descriptions denoted on the TV set.
Cautions for safety
Note: This TV set can be operated on an AC power of 240V, 50Hz. [. . . ] To select a two-digit position number (10~99) METHOD 1: Press these two numbers and the screen displays "XX -", (The period of two-press must be within 2 seconds). METHOD 2: Press 0 button first, than press these two numbers, the screen displays "0XX", the channel is selected. To select a three-digit position number (100~255) Press these three numbers and the screen displays "XXX" the channel is selected. NOTE: If the input number is over 255, the screen will remain at the current viewed program. Using the CH buttons
3 2 1 After 2 seconds X-X
X-XXXX
X-XXXXX
Press CH to select lower position numbers; CH to select higher ones.
Using the PREVIOUS channel button (
)
11 2
When there are no menus on the screen, pressing the button on the remote controller (below the MENU button) can swap the current viewed channel with the previous one. For example, the channel you previously watched is 11, the present channel is 2, press the button, it will return to channel 11, press the button again it will return to channel 2. Using the channel SCAN button
Press SCAN button, the set will scan the channels from first channel to higher channels one by one, every program will be displayed for about 3 seconds and then go on scanning until all programs are scanned over and then return to your former viewed program. During the scanning, press SCAN button again, the set will return to your former viewed program.
12
OPERATION
Convenient Picture Controls Selectable picture
To select the picture mode You can select the picture quality instantly among three preset modes and one user-set mode. BRILLIANT, NATURAL, MELLOW and PERSONAL (user-set) can be selected cyclically.
BRILLIANT NATURAL MELLOW PERSONAL
To set the desired picture quality to the PERSONAL position 1. Or press the P. M button, to call up PICTURE menu.
COLOR BRIGHT CONT SHARP 76 75 100 50
2.
Press the or button to select the desired adjusting item, and press the or button to adjust the level.
SELECT
ADJUST
Pressing (PERSONAL) Item COLOR BRIGHTNESS CONTRAST SHARPNESS *TINT paler darker weaker softer purplish deeper lighter stronger sharper greenish
BRILLIANT 75 75 100 50
NATURAL 50 50 90 40
MELLOW 50 50 70 30
* TINT is for NTSC system only. The adjusted level is stored in the PERSONAL position.
13
OPERATION
Convenient Sound Controls and Sleep timer Adjusting the volume and muting the sound
To adjust the volume Adjust the volume with the VOL buttons. Press the VOL button to increase the sound.
To mute the sound The muting function is convenient when you need to pay attention to surrounding sounds, answer a phone call, receive a visitor, etc. To restore the sound, press the MUTE button again or VOL
buttons.
Sleep timer
SLEEP timer Making use of the Sleep timer function allows you to have the set automatically turned off after a preset time, and the TV set set to standby mode. Press the SLP button every time, the time displaying on the screen will change in the sequence below:
SLEEP:30MIN.
OFF
120MIN
110MIN. . . . . . . . . . 10MIN
14
OPERATION
System setting SYSTEM SET
Press the MENU button repeatedly to select and highlight the icon, and the SYSTEM SET menu appears on the screen automatically.
LANGUAGE C. SYSTEM S. SYSTEM B. B. SET
SELECT ADJUST
ENG/ AUTO BG ON
To select the language for the OSD Making use of this function can switch the language for the OSD to either English or Chinese. The selected language is displayed in front and the screen menu is automatically displayed in that language. Colour system selection In (SYSTEM SET) menu, press the or button to select C. SYSTEM item. Press the or button to select proper colour system, AUTO, PAL, 443NTSC, 358NTSC can be selected cyclically (refer to The setting of colour system on page 11). Blue background With the blue background function ON, the TV will automatically turn blue when no signal is being received. To exit the menu, press the MENU button repeatedly or wait for 15 seconds.
LANGUAGE C. SYSTEM S. SYSTEM B. B. SET
SELECT ADJUST
ENG/ AUTO BG ON
LANGUAGE C. SYSTEM S. SYSTEM B. B. SET
SELECT ADJUST
ENG/ AUTO BG ON
LANGUAGE C. SYSTEM S. SYSTEM B. B. SET
SELECT ADJUST
ENG/ AUTO BG ON
Note: If the receiving signals are weak or are not standard, please set the B. B. SET to OFF, otherwise blue back will appear on the screen or the program will be lost.
15
OPERATION
Special functions CALENDAR function (1800-2200)
Enter into the (SPECIAL FUNCTION) menu, press the or button to select CALENDAR, press the or button to enter into calendar interface. In the calendar interface pressing the or button can switch among the year, month and the date while pressing the or button can increment or decrement them. To exit the calendar interface, press any one of the buttons on the remote controller
CALENDAR GAME1 GAME2
SELECT
ADJUST
JULY 18 2007 SU MO TU WE TH 123 8 9 10 4 5 15 16 17 11 12 22 23 24 18 19 29 30 31 25 26
FR SA 6 13 20 27 7 14 21 28
Playing games
To play GAME1 (GOBANG) Enter into the (SPECIAL FUNCTION) menu, press the or button to select GAME1 item, press the or button to enter GAME1 interface.
CALENDAR GAME1 GAME2
SELECT
ADJUST
To play GOBANG, that is, you play chess with the machine, Whoever first fills the chessboard with five continuous chessmen at the same line or diagonal line will win the game. [. . . ] The MONITOR output terminals output the video and audio signals being displayed on the screen.
To external input
MONITOR
Stereo System
To video input
Yellow (video) White (audio L/MONO) Red (audio R)
To audio inputs
(Another VTR for recording)
21
OTHERS
. Before calling service personnel, please check the following chart for a possible cause to
the trouble you are experiencing. Symptoms
No power, red indicator is not lit up Poor colour, poor tint Spots appear on the screen
Troubleshooting Guide
Check the following items
. .
Be sure the power cord is plugged in.
Contrast, colour, tint are not correctly adjusted Possible interferences of automobiles, motorcycle, trolley bus, neon lamps, etc. [. . . ]