User manual PALSONIC MODEL 6828PFS

[. . . ] Do not remove the cover to avoid danger. The TV set should be placed on an adequate place without exposing it to direct sunlight and other sources of heat to prevent the deformation of the cabinet or damage to components. Keep a space of more than 5cm from the walls to the TV set, to guarantee the good ventilation. When the TV set is to be left unattended, please turn off the power switch and remove the plug from the wall outlet. When the power cord or the plug is damaged, please contact a qualified service department to get service. 2 Installation Antenna Connection To ensure a bright-coloured and clear picture, you should use an outdoor aerial or CATV cable. Note: In case of using the Twin-lead aerial feeder (300 ) for UHF/VHF aerial, use a 300-75 ohm adaptor (not supplied) When using the coaxial cable (not supplied) (75 ) for UHF/VHF aerial, connect the plug into the 75 ohm aerial socket directly. Note: When you connect the outdoor aerial cable to the aerial terminal on the TV set, please turn off the power switch on the TV while connecting the antenna lead. [. . . ] Using the CH buttons Press CH to select lower position numbers; CH to select higher ones. 1 3 2 After 2 seconds X-X X-XXXX X-XXXXX Using the PREVIOUS channel button ( ) 11 2 When there are no menus on the screen, pressing the button on the remote controller (below the MENU button) can swap the current viewed channel with the previous one. For example, the channel you previously watched is 11, the present channel is 2, press the button, it will return to channel 11, press the button again it will return to channel 2. Using the channel SCAN button Press SCAN button, the set will scan the channels from first channel to higher channels one by one, every program will be displayed for about 3 seconds and then go on scanning until all programs are scanned over and then return to your former viewed program. During the scanning, press SCAN button again, the set will return to your former viewed program. 12 OPERATION Convenient Picture Controls Selectable picture To select the picture mode You can select the picture quality instantly among three preset modes and one user-set mode. BRILLIANT, NATURAL, MELLOW and PERSONAL (user-set) can be selected cyclically. BRILLIANT NATURAL MELLOW PERSONAL To set the desired picture quality to the PERSONAL position 1. Or press the P. M button, to call up PICTURE menu. COLOR BRIGHT CONT SHARP 76 75 100 50 2. Press the or button to select the desired adjusting item, and press the or button to adjust the level. SELECT ADJUST Pressing (PERSONAL) Item COLOR BRIGHTNESS CONTRAST SHARPNESS *TINT paler darker weaker softer purplish deeper lighter stronger sharper greenish BRILLIANT 75 75 100 50 NATURAL 50 50 90 40 MELLOW 50 50 70 30 * TINT is for NTSC system only. The adjusted level is stored in the PERSONAL position. 13 OPERATION Convenient Sound Controls and Sleep timer Adjusting the volume and muting the sound To adjust the volume Adjust the volume with the VOL buttons. Press the VOL button to increase the sound. To mute the sound The muting function is convenient when you need to pay attention to surrounding sounds, answer a phone call, receive a visitor, etc. To restore the sound, press the MUTE button again or VOL buttons. Sleep timer SLEEP timer Making use of the Sleep timer function allows you to have the set automatically turned off after a preset time, and the TV set set to standby mode. Press the SLP button every time, the time displaying on the screen will change in the sequence below: SLEEP:30MIN. OFF 120MIN 110MIN. . . . . . . . . . 10MIN 14 OPERATION System setting SYSTEM SET Press the MENU button repeatedly to select and highlight the icon, and the SYSTEM SET menu appears on the screen automatically. LANGUAGE C. SYSTEM S. SYSTEM B. B. SET SELECT ADJUST ENG/ AUTO BG ON To select the language for the OSD Making use of this function can switch the language for the OSD to either English or Chinese. The selected language is displayed in front and the screen menu is automatically displayed in that language Colour system selection In (SYSTEM SET) menu, press the or button to select C-SYSTEM item. Press the or button to select proper colour system, AUTO, PAL, 443NTSC, 358NTSC can be selected cyclically (refer to setting of colour system on page 11). Blue background With the blue background function ON, the TV will automatically turn blue when no signal is being received. To exit the menu, press the MENU button repeatedly or wait for 15 seconds. LANGUAGE C. SYSTEM S. SYSTEM B. B. SET SELECT ADJUST ENG/ AUTO BG ON LANGUAGE C. SYSTEM S. SYSTEM B. B. SET SELECT ADJUST ENG/ AUTO BG ON LANGUAGE C. SYSTEM S. SYSTEM B. B. SET SELECT ADJUST ENG/ AUTO BG ON Note: If the receiving signals are weak or are not standard, please set the B. B. SET to OFF, otherwise blue back will appear on the screen or the program will be lost. 15 OPERATION Special functions CALENDAR function (1800-2200) Enter into the (SPECIAL FUNCTION) menu, press the or button to select CALENDAR, press the or button to enter into calendar interface. In the calendar interface pressing the or button can switch among the year, month and the date while pressing the or button can increment or decrement them. To exit the calendar interface, press any one of the buttons on the remote controller CALENDAR GAME1 GAME2 SELECT ADJUST JULY 18 2007 SU MO TU WE TH 123 8 9 10 4 5 15 16 17 11 12 22 23 24 18 19 29 30 31 25 26 FR SA 6 13 20 27 7 14 21 28 Playing games To play GAME1 (GOBANG) Enter into the (SPECIAL FUNCTION) menu, press the or button to select GAME1 item, press the or button to enter GAME1 interface CALENDAR GAME1 GAME2 SELECT ADJUST To play GOBANG, that is, you play chess with the machine, Whoever first fills the chessboard with five continuous chessmen at the same line or diagonal line will win the game. Pressing the , , , buttons can move the cursor upward or downward or leftward or rightward. To exit the game, press the VOL button or the CH button. 16 OPERATION Special functions Playing games To play GAME2 (Falling Cube) Enter into the (SPECIAL FUNCTION) menu, press the or button to select GAME2 item, press the or button to enter GAME2 interface. CALENDAR GAME1 GAME2 SELECT ADJUST Press any one of , , , buttons to start the game. on the screen, there are falling cubes, pressing button can change the cubes shape, pressing , buttons can move the cubes leftward or rightward while pressing button can quicken the falling speed. When at the screen's playing area one row has been filled with cubes, the row will disappear, and your score will gain one point. If two rows disappear at the same time, your score will gain three points. [. . . ] Before calling service personnel, please check the following chart for a possible cause to the trouble you are experiencing. Symptoms No power, red indicator is not lit up Poor colour, poor tint Spots appear on the screen Stripes appear on the screen Check the following items Troubleshooting Guide . . Double images or "ghosts" Snowy picture The remote controller does not work . Even if the picture or the sound is normal, Be sure the power cord is plugged in. [. . . ]