User manual PALSONIC MODEL 76WSHD 1

[. . . ] OWNER'S MANUAL 76CM WIDE SCREEN HDTV READY MODEL: 76WSHD Type Tested Electrical Safety AS/NZS 3250 Lic 4166 Standards Australia APP No: N18748 PALSONIC CORPORATION PTY LTD 1 JOYNTON AVENUE WATERLOO NSW 2017 AUSTRALIA TEL: (02) 9313 7111 FAX: (02) 9313 7555 www. palsonic. com. au PALSONIC CUSTOMER SERVICE TELEPHONE AUSTRALIA: 1300 657 888 Congratulations on your purchase of Palsonic's HDTV ready. Contents 2. 1 2. 2 2. 3 2. 4 We recommend that you thoroughly read this manual before use to fully enjoy the many functions and excellent effects of this equipment. Retain this manual in an easily accessible location for future reference. * Screen displays and illustrations in this manual may differ from the actual ones for better visibility. Cautions for safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] All active channels will be searched or stored into the memory automatically. After auto-tune, the TV will return to the first active channel program. 4) During auto tune, pressing MENU button (1) can exit. (1) (2) (3) 7. 2 Manual search Method 2: If auto tune can not preset the desired channels, or you want to preset the desired channels one by one with the preferred channel number, please make use of SEARCH. 1) Use number buttons (4) or CH button (3) to select a channel number. 2) Enter into the PRESET menu, press CH button (3) to select SEARCH. (4) (3) (21) (1) (2 2 ) (3) 3) Press VOL button (2 1 ) to search channels from current channel to lower channel, press VOL button (2 2 ) to search from current channel to higher channel. When a channel is located, the searching stops, this channel is then memorised with the preset channel number. If the channel is not the one you desire, please keep pressing VOL or VOL button (2) to continue searching. ! Note: If you know the frequency value of the desired channel, you can directly input the value using the digit keys. 7. 3 To skip unnecessary position numbers After presetting the channels, you can skip unnecessary position numbers so that only the channels you want to watch are (4) selected with CH or CH button. (3) (1) 1) Press the number button (4) or CH (2) (2) button (3) to select a channel number (3) you want to skip. Thus, when you select channels with CH button (3), this channel will then be skipped. 4) To restore a skipped position number, select the position number you want to restore with the number buttons, enter into the PRESET menu to select SKIP X (OFF). 7. 4 Fine Tune When picture and sound's effect of a channel is poor (for example, one or two CATV channel's picture and sound are not standard), you can correct them by making use of Fine Tuning. 7. 4. 1 AFC (Auto Frequency Control) 1) Press the number buttons (4) or CH button (3) to select the channel you want to fine-tune. 2) Enter into the PRESET menu, press CH button (3) to select AFC, then press VOL button (2) to select AFC to activate it, the set begins fine-tune until the optimum picture and sound is achieved. (4) (3) (2) (1) (2) (3) To use AFC is recommended. If you are not satisfied with the effects after the AFC, you can shut down AFC and make use of FINE TUNE until you get satisfied effect. 7. 4. 2 FINE TUNE 1) Press the number buttons (4) or CH button (3) to select the channel you want to fine-tune. 2) Enter into the PRESET menu, press CH button (3) to select Fine tune, then press and hold the VOL or VOL button (2) to begin fine-tune until the optimum picture and sound is achieved. (4) (3) (2) (1) (2) (3) ! Note: if some channel's colour or sound is abnormal, it may be that the setting of the colour or the sound system is wrong, please do adjustment according to "8. 6 The setting of colour and sound system" to set the proper colour and sound system. 7. 5 VCR When receiving VCR programs, there may occur jump of the picture or bend of upper picture. Please do the following steps: Enter into the PRESET menu, press CH or CH button to select VCR item, and press VOL or VOL button to set VCR (ON). If you do not meet this problem, or the signal source is not from VCR, please shut off this function. 7. 6 The setting of colour and sound system 7. 6. 1 Use OSD button (1) PAL 6. 5MHz 100Hz MOVING Press OSD button (1), the screen will display position number, colour and sound system. Check whether the colour and sound system is correct. 7. 6. 2 The setting of colour system 1) Press the number buttons (4) or CH button (3) to select the channel you need to set the colour system. (3) 2) Enter into the PRESET menu, press (2) CH button (3) to select SYSTEM, then press VOL button (2) to select proper colour system. Every time you press VOL or VOL button (2), the colour system will change in the sequence below: AUTO PAL SECAM PAL60 N443 (4) (1) (2) (3) NTSC In normal circumstances, please set the colour system to AUTO, and the set can automatically select the proper colour system. If colour is still abnormal, then select the proper colour system manually. 7. 6. 3 The setting of sound system (4) (3) (2) (1) (2) (3) 1) Press the number buttons (4) or CH button (3) to select the channel you need to set the sound system. 2) Enter into the PRESET menu, press CH button (3) to select SOUND, then press VOL button (2) to select proper sound system. Every time you press VOL or VOL button (2), the sound system will change in the sequence below: 4. 5MHZ 5. 5MHZ 6. 0MHZ 6. 5MHZ 8. [. . . ] Press CH or CH button to move the (4) cursor and select your wanted menu item. If the value of the item is adjustable, go to the next step, otherwise go to above 3 step after completion of switch operation if you want to continue the adjustment. After completion of adjustment, select EXIT icon or press TEXT/IMAGE button to exit the SCREEN ADJUST menu. Or you can wait for some time and the OSD will automatically disappear. 14. 6 Function menu item's selection RECALL: It's used to restore parameters of the current display mode to factory default setting. [. . . ]