User manual PALSONIC TFTV580 1

[. . . ] OWNER'S MANUAL 58CM CORDLESS REMOTE LCD TELEVISION & MONITOR MODEL: TFTV580 N111 PALSONIC CORPORATION PTY LTD 1 JOYNTON AVENUE WATERLOO NSW 2017 AUSTRALIA TEL: (02) 9313 7111 FAX: (02) 9313 7555 www. palsonic. com. au PALSONIC CUSTOMER SERVICE TELEPHONE AUSTRALIA: 1300 657 888 Contents Important Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Control Panel and Back Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Back Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Please note that this does not affect the performance of your product. If an outside antenna is connected to the television equipment, be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges. An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can collide with such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits, as contact with them might be fatal. 3 Control Panel and Back Terminals Control Panel Remote Sensor Power Indicator A blue indicator lights when the power is on and a red indicator lights when in the standby mode. 1. VOL+/Press the VOL+ or VOL- button to directly increase or decrease the sound volume level; In OSD Menu, press these buttons to adjust the value or setting of each item 5. CH+/Press these two buttons to directly change the TV channel; In OSD Menu, press these buttons to choose the OSD items Note: Functions of VOL+/-, CH+/-, MENU, SOURCE and POWER are also provided to the remote control. This operation manual provides a description based on operating functions with the remote control. 4 Control Panel and Back Terminals Back Terminals AUDIO VGA VGA IN LINE Y PB COMPONENT IN PR 1. AVI inputs (Video, Audio L, R) / S-Video input Receive video/audio signals from external sources such as VCR or DVD player. Receive a S-Video signal from external source such as VCR or DVD player. AV2 inputs (Video, Audio L, R) Receive video/audio signals from external sources such as VCR or DVD player. AV outputs (Video, Audio L, R) Connect to the VCR input jacks to record programs. VGA input/Audio line in Connect to the VGA/Audio output jacks on your PC equipment 7. COMPONENT inputs (Y, Pb, Pr, Audio L, R) Connect to the audio and component output jacks of a DVD player or Set-Top Box. 5 Remote Control Unit Mute Power on/standby Direct channel selector Previous channel Channel up/down selector Stereo mode select Auto correct picture in VGA LEFT/RIGHT button: In the menu operation, adjust the selected item Access the menu Select the input signal source Volume up/down selector Sound mode select Picture mode select Display the current state UP/DOWN button: In menu operations, used to select item. Setting sleep timer 6 Remote Control Unit Batteries for the Remote Control If the remote control fails to operate the LCD TV functions, replace the batteries in the remote control. 1 Open the battery cover. 2 Insert two size-AAA batteries. (Place the batteries with their terminals corresponding to the (+) and (-) indications in the battery compartment. ) 3 Replace the cover. Effective range of the remote control Notes: 1. When the remote control will not be used for a long period of time or when the batteries are worn out, remove the batteries. Use the remote control within the effective range as shown in the figure on the left. If the remote control does not work, please check whether the batteries are exhausted or if they have been installed properly. When direct sunlight, and incandescent lighting, fluorescent lamp or any other strong light shines on the remote sensor of the TV, the remote operation can be come erratic. Do not mix different types of batteries in the remote. 7 Installation Antenna Connection Optimum reception of colour requires a good signal and will generally mean that an outdoor aerial must be used. The exact type and position of the aerial will depend upon your particular area. Note: It is recommended that the 75-ohm coaxial cable be used to eliminate interference and noise which may occur due to radio wave conditions. The aerial cable should not be bundled with the power cord and the like. Power connection Household power outlet AC-INPUT Plug into AC outlet bottom view AC cord 1. This product should be operated only from the type of power source indicated on the marking label. [. . . ] sleep time on fill all Auto B/G off 10 minutes 18 Operations In RGB/YPbPr Mode Select RGB/YPbPr mode 1 Press the SOURCE button on the unit or button on the remote control. Press LEFT/RIGHT or wait about 4 seconds and the signal source is selected. 2 Press UP/DOWN to highlight the RGB or YPbPr PC Signal Format Connect VGA input and be sure that there is VGA input signal. Note: The resolution of the LCD panel is 1280 x 768; any higher Resolution output from your PC Video card might distort the image. Auto Adjusting When VGA signal format is changed or when you switch to RGB mode from another source, the unit adjusts frequency and phase automatically to obtain the best display. During the process of auto correction, the screen displays Analog RGB Acquiring Signal, and all buttons on the set and on the remote control do not work until this process is finished. [. . . ]