User manual PALSONIC TFTV935S 1

[. . . ] OWNER'S MANUAL 93CM CORDLESS REMOTE LCD TELEVISION & MONITOR MODEL: TFTV935S N111 PALSONIC CORPORATION PTY LTD 1 JOYNTON AVENUE WATERLOO NSW 2017 AUSTRALIA TEL: (02) 9313 7111 FAX: (02) 9313 7555 www. palsonic. com. au PALSONIC CUSTOMER SERVICE TELEPHONE AUSTRALIA: 1300 657 888 Table of Contents Important Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Preparations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Using the Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Batteries for the Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] When connecting an external device, turn the power off on the panel to avoid any issues. Connect a Decoder 21-pin SCART connector Decoder How to connect: Connect the SCART Cable between the unit and the Decoder. Select Main Source To watch Decoder 1. The unit receives CVBS (VIDEO) signal and RGB signal from SCART1 interface and is able to identify the signal format automatically. To connect to external devices with AV terminals, you may use 21-pin Scart Converter to connect to SCART interface on the unit, and the unit receives CVBS (VIDEO) signal only. 9 Connections (continued) Connect a VCR SCART Cable Rear of the VCR 21 -pin SCART connector VCR How to connect: Connect the SCART Cable between the unit and the VCR. Select Main Source 1. Turn on your VCR, insert a videotape and press the Play button. Note: The unit receives CVBS (VIDEO) signal and Y/C (S-VIDEO) signal from SCART2 interface. When receiving Y/C signal, you need to select Scart 2 Y/C instead of Scart 2 AV in the source select menu. Therefore, if you find that the colour is not properly displayed, please try to select Scart 2 Y/C. To connect to external devices with AV terminals, you may use 2 I-pin Scart Converter to connect to SCART interface on the unit, then please select Scart 2 AV and the unit receives CVBS (VIDEO) signal only. 10 Connections (continued) Connect AVI or S-Video Inputs VIDEO L/MONO AUDIO R S-VIDEO AV IN / S-VIDEO IN cable S-Video VCR The unit provides Audio/Video inputs for you to connect external devices such as VCR, Video Camera or Home video game system. cable Examples of external devices that can be connected cable Video Audio Yellow (VIDEO) White (AUDIO L/MONO) Red (AUDIO R) Home video game system Video Camera How to connect: Connect the Audio/Video cables between the Audio (L/R)/Video jacks on the unit and external devices. Select Main Source 1. Press ENTER (Up/Down) to select Video or S-Video and press ENTER to confirm. Turn on the external device and play it. Note: For better video, you can use the S-Video terminal if your source supports it. If you are going to use S-Video terminal, please select S-Video instead of Video in source menu The Video input terminal on the AV IN and the S-Video input terminal share the same Audio input terminals. The S-Video is prior to Video terminal when they are connected at the same time. To view the picture rom the Video terminal, disconnect aby plug from the S-Video terminal. 11 Connections (continued) Connect a DVD Player or Home Cinema System Video cable Audio cable DVD player white (audio L) red (audio R, Pr) Green (Y) Blue (Pb) Rear of the D V D player How to connect a DVD Player or Home Cinema System using Component Video Connections: Connect the Video cable between the Y, Cb, Cr input jacks on the unit and Cb, Cr output jacks on the DVD player. Connect the Audio cable between the AUDIO input jack on the unit and AUDIO output jacks on the DVD player. To play DVD 1. Turn on your DVD player, insert a DVD disc and press the Play button. Select Main Source 1. HDMI Note: The Y, Pb, Pr outputs on your DVD player are sometimes labelled Y, Cb, Cr or Y, B-Y, R-Y. If so, connect the cables to like colours. 12 Connections (continued) Connect a product to HDMI Product with HDMI jack How to connect: Connect the HDMl cable between the HDMl input jacks on the unit and HDMl output jacks on the product. Note: The HDMl Sources are compatible with DVI displays through the use of a passive cable converter. Connect a passive cable converter between the HDMl input jack on the unit and DVI output jack on the product. Select Main Source Connect an Audio cable between the AUDIO output on your product and 1. Video AUDIO input jack of D-Sub IN on the unit. To Watch your Product 1. HDMI Connect a PC Audio cable D-Sub cable How to connect: PC Connect a D-Sub cable between the S-Sub interface on the PC the D-Sub interface on the unit. Connect an Audio cable between the AUDIO output on the PC and AUDIO input jack on the unit. Select Main Source 1. [. . . ] News, weather and sports information, stock exchange prices and programme previews are among the many services available. Teletext Mode Teletext is turned on/off with the TEXT button on the remote control unit. You can operate your System in Teletext mode directly by inputting commands with the remote control unit. Turning On or Off Teletext Select a TV channel providing the Teletext program. Press the TEXT button again to switch back to TV screen. TELETEXT Button Functions ENTER (Up/Down) Changing Teletext pages. Colour (RED/GREEN/YELLOW/BLUE) You can select a group or block of pages displayed in the coloured brackets at the bottom of the screen by pressing the corresponding colour (RED/GREEN/ YELLOW/BLUE) on the remote control unit. [. . . ]