User manual PALSONIC VCR-2110-CONNECTIONSETTING CHANNELSSETTING TIMERTROUBLE SHOOTING

[. . . ] AV : Turn on the TV and select the video position Press the OPERATE button, then start from "initial Settings" on the next page. Initial Settings. 1. Then, press the MENU button for 3 seconds or more and make sure that the Multi-display is changed as shown in the illustration at right. If your TV receiver does not have a position designed for Videorecorder use, select a position that is not being used by a broadcaster, then adjust the tuning on the TV (UHF channel 32) so that the TEST screen is clearly displayed. If you TV has the search function for every position, seek a channel until TEST screen appears and then store it. 1. [. . . ] Call the MENU screen, then press the and SHIFT buttons to select CHANNEL PRESET. Press the number 5 and 6 buttons during step 3 to perform Fine tuning. Automatic Channel Changing In step 3, the channel can be set as follows using the SHIFT button. Then, press the SHIFT button. channel positions 01 and 03 are interchanged. Press the SHIFT button to set one channel number into two or more positions. To skip the stored position When the stored program is not required, press the RESET button. To change the stored channel To select the desired CHANNEL, press the button. Press the MENU button TWICE to return to the normal TV screen. channel 001 is memorized in both position 01 and 03. Selecting AUX Position AU: Input from the AUDIO/VIDEO socket on the rear panel. 3 BASIC OPERATION Playback a Video Cassette LOADING EJECTING Insert a cassette tape with its labeled side up as shown In the cassette compartment. The cassette will be automatically drawn inside the compartment. STOP REWINDING * FAST FORWARDING * PLAYBACK SLOW REVERSE SEARCH ** PICTURE CONT FORWARD SEARCH ** STILL FRAME ADVANCE * During FF/REW Hold ** During SEARCH, press or or to change to SEARCH to change to FF/REW Slow Playback Press this button to start Slow Playback at 1/6, 1/2, 1/25 speed during PLAYBACK. Each press of the SLOW button in this mode changes the playback speed in 3 steps. Picture Control Press these buttons to obtain the desired picture enhancement. This function is also available in the Slow Playback and Still Frame modes. Frame Advance Each time the PLAY button is pressed while in the still mode, the picture advances one frame. . NOTES During SLOW PLAYBACK, use the buttons to move the noise bars up or down. During STILL FRAME, use the buttons to eliminate the shake of the picture screen. The colour of the picture may be lost during picture search in the LP mode. If the VCR is left in the Still/Slow playback mode for more than 5 minutes, it will automatically return to the playback mode to prevent damage to the tape. A tape recorded in the LP mode can be played back, but special playback functions such as still and slow playback are not guaranteed. 4 Digital Tracking Control Auto Tracking When playback starts or the playback speed is changed during playback, the VCR enters the Auto tracking mode. At this time, the indication "DT" blinks on the multi-display for a few seconds. Auto Operation Functions Full Auto Playback (With VCR power OFF) 1. The tape is ejected and the VCR is turned off. Manual tracking If noise still appears (picture and sound) : Press the button during PLAYBACK until the best picture is obtained. Press the PLAY button for 2 SECONDS to return to the Auto tracking mode. !NOTE The noise on the screen may not be completely removed depending on the tape used, especially when the tape has been recorded on another VCR. Auto Playback (With VCR power ON) 1. The VCR is not turned off. 1 Minute Skip . With this feature, you can skip over one minute's worth of commercials recorded on a tape. NOTE The Auto Playback or Full Auto Playback mode is released if one of the tape related buttons (FF, REW, PAUSE, STOP/ EJECT, PLAY or OPERATE) is pressed. Auto Turn on When a cassette tape with a safety tab is inserted with the VCR turned off, the VCR will be automatically turned on. Zero Return 1. Press the RESET button during RECORDING or PLAYBACK to set the counter to 0:00:00 at a scene you wish to watch again. The VCR will go into FF or REW mode until the counter setting is 0:00:00 Auto Rewind When a tape reaches its end, (except during FF, OTR, Index search / scan, and programmable timer recording), it will automatically be rewound to its beginning and the unit will switch to the stop mode. Auto Power off (Select by MODE screen, page 7) If no action is executed for 10 minutes in the STOP mode or for 10 minutes in the EJECT mode, the unit is automatically turned off to save electricity. Auto Repeat During PLAYBACK, press the No. 1 key on the remote control, then Playback of the tape will be repeated from beginning to end, and the repeat mark will be displayed on OSD. 1 key again. 5 Index Search Function You can easily locate the desired programme using the Index signal registered on the tape. ! [. . . ] Plug the power cord into the outlet again one minute after it was disconnected. Press the CLEAR (RESET) button on the rear panel to clear the data stored in the unit's memory and input the data again. After the CLEAR (RESET) button is pressed, wait for about 2~3 minutes before connecting the power cord again. Set the VCR in the VCR mode by pressing TV/VCR button. Clock setting has not been done. [. . . ]