User manual PANASONIC AG-VP310

[. . . ] Initial Setup (Connection) Basic Operation VCR Operation DVD/VCR DECK Operating Instructions Model No. AG-VP310 Professional / Industrial Video Connections and Initial Setup Procedures are on pages 12 to 17. DVD Operation MULTI FORMAT PLAYBACK For Your Information *Ability to play back may depend on recording conditions. As an ENERGY STAR ® Partner, Matsushita Electric Corporation of America has determined that this product or product model meets the ENERGY STAR ® guidelines for energy efficiency. LSQT0844 A Please read these instructions carefully before attempting to connect, operate or adjust this product. Please save this manual. Important Safeguards and Precautions TO REDUCE THE RISK OF ELECTRIC SHOCK, FIRE, INJURY TO PERSONS OR DAMAGE TO THIS PRODUCT, READ AND RETAIN ALL SAFETY AND OPERATING INSTRUCTIONS. HEED ALL WARNINGS IN THE MANUAL AND ON THE PRODUCT. INSTALLATION POWER SOURCE CAUTION Operate only from a power source indicated on the unit or in this manual. [. . . ] · When recording programs via an antenna or cable, DSS Receiver must be turned off. 25 MTS Broadcast/ VHS Hi-Fi Stereo System Connection Make the Audio/Video Connection as shown on pp. 12 ~ 15. · You can use TV connected to a Stereo amplifier and speakers instead of Stereo TV. Receivable Broadcast Types The following are possible audio broadcast types and onscreen displays. The signal being received is indicated with a " " mark while the selected audio mode is indicated with an arrow. MTS Stereo and SAP broadcast Multi-channel Television Sound Stereo (main language) and Secondary Audio Program (sub language) broadcasts are being received simultaneously. Select STEREO or SAP audio mode. STOP STEREO SAP MONO 1 2 : 0 0AM CH 02 0 : 00 : 00 SP MTS Stereo broadcast Multi-channel Television Sound Stereo broadcast. Select STEREO audio mode. · If stereo broadcast is weak and display flickers, select MONO audio mode for possible better results. AUDIO STOP STEREO SAP MONO 1 2 : 0 0AM CH 02 0 : 00 : 00 SP (SAP/Hi-Fi) DISPLAY SAP broadcast Secondary Audio Program (sub language) broadcast. Select SAP audio mode for the sub language. STOP STEREO SAP MONO 1 2 : 0 0AM CH 02 0 : 00 : 00 SP MONO broadcast Normal monaural sound broadcast. STOP STEREO SAP MONO 1 2 : 0 0AM CH 02 0 : 00 : 00 SP ® Equipped with -TV Noise Reduction for true MTS reproduction. ® -TV Noise Reduction is required for good stereo separation and audio ® fidelity. is a registered trademark, ® and is licensed by Technology Licensing. 26 *Important: If a remote control button does not work when pressed, press the VCR button on the remote and try the button again. Audio Mode for Recording 1 2 3 Press AUDIO (SAP/Hi-Fi) to display audio mode. (Display disappears after 5 seconds. ) STEREO SAP MONO Press AUDIO (SAP/Hi-Fi) repeatedly to select desired mode. · Refer to "Receivable Broadcast Types" on p. 21. VCR Operation Audio Mode for Playback 1 2 3 Start playback. Press AUDIO (SAP/Hi-Fi) repeatedly to select desired mode. · Select "HIFI (L/R)" or "HIFI (L)" or "HIFI (R)" to listen to stereo recordings in stereo sound. · Display disappears after 5 seconds. H I F I : L/R HIFI : L HIFI : R NORMAL · Arrow indicates selection. Notes · Only tapes recorded in Hi-Fi stereo will playback with true stereo sound. · To listen to Hi-Fi stereo playback, the DECK AUDIO (L/R) jacks must be connected to a stereo TV or an external stereo amplifier and speakers. 12, 14. ) · If tracking is adjusted during playback, Hi-Fi audio may revert to normal audio. · Hi-Fi and normal audio playback volume level may differ. 27 Multi-Brand Control Feature Multi-Brand Control Setup The Remote Control can be set to control some TVs. 1 2 3 Find your TV Brand Code Number on the following page. Set up for TV control, hold down TV button, enter code with NUMBER keys. Confirm code entry, press POWER to turn selected unit on or off. · Remote will not control every TV made by the manufacturer listed. If your product is not listed, then the remote is not compatible with that product. Notes Using Multi-Brand Control After remote is set up, you can select VCR, DVD, or TV for the desired function. Press VCR, DVD, or TV on the remote. (Table below shows available remote buttons for each mode. ) Mode Unit DVD/VCR All EJECT/OPEN/CLOSE *, DISPLAY, PLAY, STOP, FF/SLOW+, REW/SLOW-, VCR/TV, PAUSE/STILL, SKIP, AUDIO, CM/ZERO, SPEED, REC, TAPE POSITION, PAGE, COUNTER RESET TV VOL +/- DVD VCR POWER, INPUT, NUMBER keys, ENTER, CH / , VOL +/- TV * Notes Bold: VCR Function Italic: DVD Function Bold Italic: VCR and DVD Functions Normal: TV · Not all functions listed may be controllable. · In TV mode, it may be necessary to press ENTER after pressing NUMBER keys for channel selection. 28 TV Brand Code Numbers Panasonic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 02 02 03 03 04 05 05 07 08 Toshiba . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15, 16, 09 10 10 11 12 13 14 17 Important Notes · Some manufacturers use several codes for one brand. · Some TVs require you to turn on the power manually. VCR Operation POWER TV NUMBER keys VCR DVD ENTER 29 Tape Operation Search System For each recording, an invisible index mark is placed on the tape. [. . . ] · The picture will be somewhat distorted at times: this is normal. · Some discs may have sections which prohibit Forward/Reverse Scene Search. 23) · If the audio soundtrack and/or subtitle language selected at DVD initial settings does not exist on the disc, it will not be accessible. · "OFF" is selected at the changing subtitle language. [. . . ]