User manual PANASONIC BM-ET500

[. . . ] Iris Camera Operating Instructions Model No. BM-ET500 ACCEPT REJECT READY Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. Cautions: · This unit is for indoor use only. · Before attempting to connect or operate this product, please read the label on the bottom. For U. S. A CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. [. . . ] Refer to the control unit's operating instructions for how to turn on/off the power. · When you use an external power supply device, do the following: Turn on the external power supply device before turning on Control Unit BM-ED500. Turn off the external power supply device after turning off the control unit. · The third-party external power supply must be a UL Listed access control power limited device. · Consumable part Contact your dealer for the front panel replacement, for example, when it is damaged or when you cannot recognize or enroll yourself. Part number of the front panel: 3CF001017AAA · Use of near-infrared ray Near-infrared ray is used when iris data is enrolled or recognized by the unit. The near-infrared ray is compliant with the radiological safety standard of IEC60825-1. · Indication Refer to the bottom of the unit as to the indications of equipment classification and power source, etc. · If you are in a situation that iris recognition is impossible from the exterior, recognition or enrollment will be invalid. Take enough care not to leak the image data out of the administration PC. It is also recommended that you should get an agreement from a person to register his or her data. · Do the self-diagnostic test, when you open this unit door for maintenance, etc. The self-diagnostic test can be carried out by turning on a power supply. Read BM-ED500 Operating instructions for turning on a power supply. 9 MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS q Status indicator ACCEPT REJECT READY w User guidance indicators e Built-in color CCTV camera r Operation indicators t Front panel y 10 key cover u LED indicator 1 6 2 7 3 8 4 9 5 0 CANCEL ENTER o Buzzer-level adjustment hole i Numeric keys q Status Indicator Shows the status of recognition or enrollment. * Or lights up when enrollment has been successfully executed through iris image capturing. REJECT: Lights up when recognition has not been successfully executed. Or lights up when enrollment has not been successfully executed through iris image capturing. When this indicator is blinking, recognition/enrollment is unavailable. * Depending on capturing condition, you might not enroll your iris data even when ACCEPT is lighting. After the enrollment, confirm through the administration PC, in which the administration software is installed, if the recognition has been successfully executed. w User guidance indicators These indicators light up when you stand in front of the unit, and then inform you that recognition/enrollment will start. For example, it is used for status confirmation if a recognition has not been successfully executed. r Operation indicators These indicators show the operation statuses of the unit. [. . . ] · Public information such as your birthday or phone number · Repeated numerics such as 1111 or 7777 · Sequential numerics such as 1234 or 7890 Note: The digit number differs depends on the system environment. When you have forgotten your ID or password, contact the system administrator. 17 ADDITIONAL SYSTEM COMPONENTS I Control Unit BM-ED500 I Administration Software BMES500E Administration Software BM-ES500E This product is necessary for administering iris data, ID data and passwords. This product is necessary for iris data recognition/enrollment and controlling an electric lock. 18 TROUBLESHOOTING Check to see the following before request for repair. If a trouble cannot be corrected even after checking and trying remedy, contact your dealer. Problem System does not power up. Check item The power of the control unit may be turned off. (The control unit supply the power to the unit. ) Third party external power may be off. [. . . ]