User manual PANASONIC CQ-5330

[. . . ] R Heavy Duty CD player/weather Band Receiver with CD changer Control/XM Radio Ready CQ-5330U CLK PWR ALM VOL PUSH SEL / SAT DISP CQ-5330U LOUD Operating Instructions TUNE SEEK MODE DISC CD SCAN RPT RDM MUTE BAND BASS/TREB/BAL/FADER SCAN ILL 1 APM 2 3 4 5 6 · Please read these instructions carefully before using this product and keep this manual for future reference. Safety Information WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK OR PRODUCT DAMAGE, DO NOT EXPOSE THIS APPLIANCE TO RAIN, SPLASHING, DRIPPING OR MOISTURE. The following applies only in the U. S. A. Part 15 of the FCC Rules FCC Warning: Any unauthorized changes or modifications to this equipment would void the user's authority to operate this device. CAUTION: PLEASE FOLLOW THE LAWS AND REGULATIONS OF YOUR STATE, PROVINCE OR COUNTRY FOR INSTALLATION OF THE UNIT. Laser Products: Wave length: 780 nm Laser power: No hazardous radiation is emitted with safety protection. TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, AND ANNOYING INTERFERENCE, USE ONLY THE INCLUDED COMPONENTS. NOTICE: This product contains lead in some components. Disposal of these materials may be regulated in your community due to environmental considerations. [. . . ] · Press and hold [6] (RDM) for more than 2 seconds again to cancel Remote Control CA-RC500U (option) 15 CQ-5330U XM Control Preparation: Connect the XM receiver (XM DIRECT MODEL:XM-RVR-D-001) to the Unit CQ-5330U. XM satellite radio is available on a chargable basis. q XM Mode (When a XM receiver is connected. ) Press [MODE] to change to the XM mode. CLK r Channel Scan Press [SCAN], each channel in ascending order will be scanned sequentially and the display will blink for 5 seconds. Press [SCAN] again to stop scamming and the last channel will continue to broadcast. PWR ALM VOL PUSH SEL / SAT DISP CQ-5330U LOUD MODE DISC CD SCAN RPT RDM MUTE TUNE SEEK SCAN ILL BAND BASS/TREB/BAL/FADER 1 APM 2 3 4 5 6 w Band Press [BAND]. [CATEGORY] XM displays as follows, (Example) Satellite Radio after 2 seconds Indicator e Channel Selection Press [}]: Up Press [{]: Down Press and hold [}] or [{] for more than 2 seconds to change channels rapidly. XM Band Preset Number Channel Number after 5 seconds Channel Name Category Priority Setting and Selecting · Push the knob [SEL] for more than 2 seconds. (Push and hold) (without operation during 2 seconds. ) (when category is set ON. ) (without operation during 5 seconds. ) category name (interdisplay for 2 seconds. ) turn left (blinks) turn right (when category is set OFF. ) 16 CQ-5330U · When the display shows "CAT ON", Press [2] (}): Up Press [1] ({): Down 1 2 1 2 (without operation during 5 seconds. ) Category Name Press [2] or [1]. (Receiving) (Received) Category Name (interdisplay for 2 seconds. ) Push and hold the knob [SEL] for more than 2 seconds to resume the normal display. category on indicator Notes: CAT OFF: Every channel can be selected from every category. Default: CAT OFF Manual Preset Memory Up to 6 channels each can be saved in the XM1, XM2 and XM3 preset station memories. q Select a band and a channel. BAND TUNE SEEK w Press and hold [1] to [6] for more than 2 seconds to memorize. 1 2 3 4 5 6 · The channel number and the preset number blink once. Note: Existing saved channels are overwritten with new channels after the above procedure. Preset memory Calling q Select a band. BAND w Press [1] to [6]. 1 2 3 4 5 6 Note: When category is on category will be off after pressed any preset button [1] to [6]. 17 CQ-5330U XM Control (Continued) Display Change Press and hold [MODE] (DISP) for more than 2 seconds. MODE Channel name (Press and hold) (Reading artist name) Artist name (Reading song title) song title (Reading categry) Category name Note: Display when there is no name/title or can not decode. XM ID Confirmation · Push and hold the knob [SEL] for more than 2 seconds and then push again during 2 seconds. (Push and hold) (Push) Note: If the ID number is 12345678 for example. · Push the knob for more than 2 seconds to resume to the previous mode when displaying "RADIO ID" or ID number. · You can also see ID number by selecting CH0. Error display XM ID is or communication fails, Press [MODE] to another mode. 18 CQ-5330U Troubleshooting Preliminary Steps Check and take steps as described in the tables below. If You Suspect Something Wrong Immediately switch the power off. Disconnect the power connector and check that there is neither smoke nor heat from the unit before asking for repairs. Never try to repair the unit by yourself because it is dangerous to do so. Cautions: · Do not use the unit if it malfunctions or if there is something wrong. · Do not use the unit in irregular condition, for example, without sound, or with smoke or foul smell, which can cause ignition or electric shock. Immediately stop using it and call the store where you purchased it. Troubleshooting Tips Common Trouble Cause/Step Vehicle's ignition switch is not on. a Connect cables correctly. Noise. The ground lead is not connected properly. a Connect the ground lead properly. 19 CQ-5330U Troubleshooting (Continued) Radio Trouble Cause/Step Station is too far, or signals are too weak. a Connect the battery cable to the terminal that is always active. Much noise in FM stereo and monaural broadcasts. Preset station is reset. CD Trouble Cause/Step Disc is upside down. a The unit may not successfully playback a CD-R/RW that is made in combination of writing software, a CD recorder (CD-R/RW drive) and a disc which are incompatible one another. a The unit may not successfully playback a CD-R/RW that is made in combination of writing software, a CD recorder (CD-R/RW drive) and a disc which are incompatible one another. [. . . ] Bolt (5mmø × 25 mm) Toothed Lock Washer (5mmø) Removal Tool (U-shaped) Antenna Connector Diagram Q'ty 1 2 2 2 1 1 1 2 1 · Remove Mounting Collar q from the main unit temporarily, which are already mounted at shipment. * Caution: Various settings that have been stored in the memory in other on-board equipment (vehicle navigation etc. ) may be lost if the battery terminals are disconnected. Therefore, we recommend to make a record of or to back up the settings before disconnecting the terminals. After completing installation of the main unit, set the equipment again according to the record. · Unit should be installed in a horizontal position with the front end up at a convenient angle, but not more than 30°. o (a) Using the rear support strap t Dashboard Installation Installation Opening This unit can be installed in any dashboard having an opening as shown below. [. . . ]