User manual PANASONIC CQ-DF201U

[. . . ] Removable Full Front High-Power CD Player/ Receiver CQ-DF201U BAN D APM/SCAN 45WX4 CD RECEIVER bright display with level meters OPEN LEVEL Récepteur/lecteur CD à puissance élevée avec panneau avant entièrement amovible Reproductor CD/receptor de alta potencia con placa frontal completamente removible VOL TUNE TRACK E REMOT L SE MUTE CLOCK DISP SOURCE · PWR 7 1 8 2 9 3 10 4 11 5 12 6 RANDOM LOUD REP MONO/LOC CQ-DF201U Operating Instructions Manuel d'instructions Manual de instrucciones Please read these instructions carefully before using this product and save this manual for future use. Prière de lire ces instructions attentivement avant d'utiliser Ie produit et garder ce manuel pour l'utilisation ultérieure. Lea con atención estas instrucciones antes de utilizar el producto y guarde este manual para poderlo consultar en el futuro. E N G L I S H Safety Information Radio Frequency Interference Statement: Applies only in U. S. A. This equipment has been tested and found to comply with the limits for a Class B digital, pursuant to Part 15 of the FCC Rules. [. . . ] Battery Information: Battery type: Panasonic lithium battery (CR2025) (included) Battery life: Approximately 6 months with normal use (at room temperature) Caution: Improper use of batteries may cause overheating, an explosion or ignition, resulting in injury or a fire. Be careful to the local disposal rules when you dispose of batteries. Hours 2 Press and hold [DISP] (CLOCK). (End. ) Note: Press and hold [# TUNE] or [" TUNE] to change numbers rapidly. Note: The [DISP] (CLOCK) button will not work while the CD player is set to the scan play mode. Broadcast station In CD player mode: Playing time When the power is off: Clock display No display Clock display Clock display Main Controls Buttons of the remote control function in the same way as the controls on the main unit of the reference page. (ATT) Power button ( page 10) MODE button ( pages 12, 14) PWR MUTE MUTE button ( page 10) Volume control buttons ( page 10) MODE VOL Time Reset Press and hold [DISP] (CLOCK) for more than 2 seconds to activate the time setting mode to reset the time. BAND button ( page 12) PRG BAND/DISC UP TUNE TRACK TUNE/ TRACK buttons ( pages 12, 15) Car Audio 16 CQ-DF201U CQ-DF201U 17 E N G L I S H 9 Installation Guide Identify All Leads WARNING This installation information is designed for experienced installers and is not intended for non-technical individuals. It does not contain warnings or cautions of potential dangers involved in attempting to install this product. Any attempt to install this product in a motor car by anyone other than qualified installer could cause damage to the electrical system and could result in serious personal injury or death. The first step in installation is to identify all the car wires you'll use when hooking up your sound system. As you identify each wire, we suggest that you label it using masking tape and a permanent marker. Note: Do not connect the power connector to the stereo unit until you have made all connections. If there are no plastic caps on the stereo hooking wires, insulate all exposed leads with electrical tape until you are ready to use them. Power Lead If your car has a radio or is pre-wired for one: Cut the connector wires one at a time from the plug (leaving the leads as long as possible) so that you can work with individual leads. If your car has a radio or is pre-wired for one: With the ignition and headlights off, identify the car battery lead by grounding one lead of the test bulb to the chassis and checking the remaining exposed wires from the cut radio connector plug. f your car is not wired for an audio unit: Go to the fuse block and find the fuse port for the battery, usually marked BAT. A handy way to identify the speaker leads and the speaker they are connected with is to test the leads using a 1. 5 volt AA battery as follows. Hold one lead against one pole of the battery and stroke the other lead across the other pole. You will hear a scraping sound in one of the speakers if you are holding a speaker lead. If not, keep testing different lead combinations until you have located all the speaker leads. Antenna Motor If your car is equipped with an automatic power antenna, identify the car motor antenna lead by connecting one bulb tester lead to the car battery lead and touching the remaining exposed wires from the cut radio connector plug one at a time. You will hear the antenna motor activate when you touch the correct wire. Antenna The antenna lead is a thick, black wire with a metal plug at the end. E N G L I S H 10 Installation Hardware No. nut (5 mm·) Rear support strap Tapping screw (5 mm·a16 mm) Mounting bolt (5 mm·) Power connector Removable face plate case Trim plate Diagram Q'ty 1 1 1 1 1 1 1 1 If you encounter problems, please consult your nearest professional installer. Caution: This unit operates with a 12 volt DC negative ground auto battery system only. [. . . ] Preset station is reset. 24 CQ-DF201U 25 E N G L I S H 17 Troubleshooting (Continued) CD Trouble Cause/Step CD is upside down. Mount the unit securely with the mounting parts, referring to the section on installation. If normal operation is not restored yet, call the store where you purchased the unit or the nearest service station to ask for repairs. Remote Control Trouble Cause/Step Battery polarities (i) (j) are reversed. Direct the remote control at sensor (REMOTE) on the panel. E N G L I S H 18 CD is inside but no sound. CD sound skips, tone quality is low. Buttons are invalid for operation. Sound skips due to vibration. Error Display Messages CD Display Cause/Step Disc is dirty, or is upside down. [. . . ]