User manual PANASONIC CQ-DP383U SIRIUS

[. . . ] This could cause electrical shorts, fire, or other damage. Use Authorized Servicenters Do not attempt to disassemble or adjust this precision product. Please refer to the Servicenter list including with this product for service assistance. When Parked Parking in direct sunlight can produce very high temperatures inside your car. Give the interior a chance to cool down before switching the unit on. For Installation This product should be installed in a horizontal position with the front end up at a convenient angle, but not more than 30x. Use the Proper Power Supply This product is designed to operate with a 12 V DC, negative ground battery system. Components Operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Installation hardware. . . . . . . . . . . . . . . . 1 set ( page 28) Power connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] ( page 15) STD : Standard spectrum analyzer display (9 bands) Contrast Allows you to adjust the display contrasts for better viewing. SET #]/["] or [#] to select [TUNE $]/[$]: level up [TUNE %]/[%]: level down Press [BAND] (SET) to set. CONTRAST Press [BAND] (SET) to set. SET #]/["] or [#] to select AUDIO PICTURE Clock on the Mode Display Default: ON ("--:--" will appear before adjusting the clock. ) Press [BAND] (SET) to select ON OFF : Clock display ON : Clock display OFF Clock display FUNCTION CLOCK-OFF CLOCK-ON Press [P. SET #]/["] or [#] to select Hour/Minute Switch [TUNE %]/[%]: The hour display high lights. [TUNE $]/[$]: The minutes display high lights. Hour/Minute Adjustment [P. SET #]/[#]: Put back hour/minute. Clock Adjustment (12 hour system) Default: Not adjusted. CLOCK ADJ Press [BAND] (SET) to set. Press [BAND] (SET) to set. CQ-DP383U SIRIUS 24 CQ-DP383U SIRIUS 25 E N G L I S H 17 User Settings [MENU] [BAND] (SET) REMOTE SET/AUTO·P ;/1 [DISP] Function menu display CQ-DP383U SIRIUS MOSFET POWER SOURCE 1 2 RAND BAND 50WX4 OPEN DISP 3 VOL SCAN 4 REP VOL MENU P·SET CH·C !@ D·M PWR TUNE TRACK DISC MUTE S·HDB SOURCE 5 6 MENU DIM HDB CD RECEIVER WIITH FULL DOT MATRIX DISPLAY [P. SET "] [P. SET #] (MENU SELECT) ["] [#] (MENU SELECT) MUTE SEL BAND [SEL] (MENU) [BAND] (SET) [DISP] Notes: Operations except setting should be performed after returning to the mode display. The display returns to the previous one with no operation for 15 seconds after changing to the menu display. Press [DISP] to return to the regular mode. E N G L I S H 18 DISP Car Audio 1 Menu Mute/Attenuator You can select how much to lower the volume when [MUTE] is pressed. SET #]/["] or [#] to select 3 Setting Press [BAND] (SET) to switch between MUTE (mute) or ATT (attenuator) in turn. : Decrease the volume to 1/10. MUTE KEY Excluding AUX-IN from Source Selection Default: ON Press [MENU]/ [SEL] (MENU) to select "FUNCTION" on the menu display. Touch the other lead of the test bulb to each of the exposed wires from the cut radio connector plug. Touch one wire at a time until you find the outlet that causes the test bulb to light. If your car is not wired for an audio unit: Go to the fuse block and find the fuse port for radio (RADIO), accessory (ACC), or ignition (IGN). Connect All Leads Now that you have identified all the wires in the car, you are ready to begin connecting them to the stereo unit wires. The wiring diagram ( pages 34j35) shows the proper connections and color coding of the leads. We strongly recommend that you test the unit before making a final installation. You can set the unit on the floor and make temporary connections to test the unit. Important: Connect the red power lead last, after you have made and insulated all other connections. Ground Connect the black ground lead of the power connector to the metal car chassis. Required Tools You'll need a screwdriver, a 1. 5 V AA battery, and the following: 12 V DC Electrical Side-cut Test bulb tape pliers Overview This product should be installed by a professional. However, if you plan to install this product yourself, your first step is to decide where to install it. The instructions in these pages will guide you through the remaining steps: (Please refer to the "WARNING" statement above. ) Identify and label the car wires. Check the operation of the unit. Dashboard Specifications Thickness Min. [. . . ] Never try to repair the unit yourself because it is dangerous to do so. Cautions: Do not use the unit if it malfunctions or is something wrong. Do not use the unit in abnormal condition, for example, without sound, or with smoke or foul smell, can cause ignition or electric shock. Immediately stop using it and call the store where you purchased it. E N G L I S H 28 Troubleshooting Tips Common Trouble Cause/Step Car's engine switch is not on. Turn your car's ignition switch to ACC or ON. Extension cord (supplied for CX-DP88U/N) Cables are not correctly connected. [. . . ]