User manual PANASONIC CQ-DP875

[. . . ] This could cause electrical shorts, fire, or other damage. Use Authorized Servicenters Do not attempt to disassemble or adjust this precision product. Please refer to the Servicenter list including with this product for service assistance. C H I N E S E When Parked Parking in direct sunlight can produce very high temperatures inside your car. Give the interior a chance to cool down before switching the unit on. For Installation This product should be installed in a horizontal position with the front end up at a convenient angle, but not more than 30x. Use the Proper Power Supply This product is designed to operate with a 12 V DC, negative ground battery system. Components Operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Installation hardware. . . . . . . . . . . . . . . . 1 set ( page 26) Power connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The first 10 seconds of each track on the disc are played in sequence. Press [BAND] (SCAN) again to cancel. DISC TRACK 24 CQ-DP151/DP101W CQ-DP151/DP101W 25 E N G L I S H 9 Installation Guide Identify All Leads WARNING This installation information is designed for experienced installers and is not intended for non-technical individuals. It does not contain warnings or cautions of potential dangers involved in attempting to install this product. Any attempt to install this product in a motor car by anyone other than qualified installer could cause damage to the electrical system and could result in serious personal injury or death. The first step in installation is to identify all the car wires you'll use when hooking up your sound system. As you identify each wire, we suggest that you label it using masking tape and a permanent marker. Note: Do not connect the power connector to the stereo unit until you have made all connections. If there are no plastic caps on the stereo hooking wires, insulate all exposed leads with electrical tape until you are ready to use them. Power Lead If your car has a radio or is pre-wired for one: Cut the connector wires one at a time from the plug (leaving the leads as long as possible) so that you can work with individual leads. If your car is not wired for an audio unit: Go to the fuse block and find the fuse port for the battery, usually marked BAT. A handy way to identify the speaker leads and the speaker they are connected with is to test the leads using a 1. 5 V AA battery as follows. Hold one lead against one pole of the battery and stroke the other lead across the other pole. You will hear a scraping sound in one of the speakers if you are holding a speaker lead. If you have difficulties, consult your nearest authorized professional installer for assistance. Installation Procedures First complete the electrical connections, and then check them for correctness. ( page 32) mounting collar 1 Insertthe mounting tabs1 into thea dashboard, and bend out with screwdriver. Make sure that the lock lever (§) is flush with the mounting collar 1 (not projecting outward). Lock lever (§) E N G L I S H 12 Preparation We strongly recommend that you wear gloves for installation work to protect yourself from injuries. When bending the mounting tabs of the mounting collar with a screwdriver, be careful not to injure your hands and fingers. Disconnect the cable from the negative - battery terminal (see caution below). Unit should be installed in a horizontal position with the front end up at a convenient angle, but not more than 30o. 6 Power connector Lock lever (§) Mounting tabs 5 Mounting bolt unit. 2 Secure the rear of thebolt 5 and power connector After fixing mounting 6, fix the rear of the unit to the car body by either method (a) or (b) shown below. Less than 30x 3 Insert trim plate 7. 4 After installation, reconnect battery terminal. the negative - Caution: Do not disconnect the battery terminals of a car with a trip or navigational computer since all user settings stored in memory will be lost. Instead take extra care with installing the unit to prevent shorts. (a) Using the rear support strap 3 Fire wall of car 4 Tapping screw (5 mm·a16 mm) 3 mm· 2 Hex. [. . . ] 6 Item Power connector Q'ty 1 Troubleshooting Preliminary Steps Check and take steps as described in the tables below. If You Suspect Something Wrong Immediately switch power off. Disconnect the power connector and check that there is neither smoke nor heat from the unit before asking for repairs. Never try to repair the unit yourself because it is dangerous to do so. Cautions: Do not use the unit if it malfunctions or is something wrong. Do not use the unit in abnormal condition, for example, without sound, or with smoke or foul smell, can cause ignition or electric shock. [. . . ]