User manual PANASONIC CQ-HX2083U

[. . . ] Press. 2 (Example: STORM) 3 E N G L I S H (Example: PATTERN 1) For details on how to perform menu operations using the remote control, refer to page 28. Note: Press [MENU] or [DISP] (display) on the remote control to return to the regular mode. Press /[RET] (RETURN) to return to the previous display. 22 1 Menu Display Color Changing Pattern (STORM) This is used to select the pattern that changes the colors of the display area. Default: PATTERN 1 Setting range: PATTERN 1 to PATTERN 4 2 Submenu 3 Set : PATTERN 1 : PATTERN 2 : PATTERN 3 : PATTERN 4 Direct Operation In the case of remote control, as an alternative to performing operations from the menu, the operations can be performed directly using the buttons shown below. SOURCE PWR BAND RETURN RET MENU [FACE] FACE S ·A S·A DIMMER DISP DIM ET S Base Color Selection (LEVEL) This is used to select the display colors which are to be changed in line with the variations in the music level. [. . . ] The product should be serviced only by a qualified technician. Do not use irregular shaped discs. Notes on CD-Rs/RWs You may have trouble playing back some CDR/RW discs recorded on CD recorders (CD-R/RW drives), either due to their recording characteristics or dirt, fingerprints, scratches, etc. CD-R/RW discs are less resistant to high temperatures and high humidity than ordinary music CDs. Leaving them inside a car for extended periods may damage them and make playback impossible. The unit may not successfully play back a CDR/RW that was made by the combination of writing software, a CD recorder (CD-R/RW drive) and a disc if they are incompatible one another. This player cannot play the CD-R/RW discs if the session is not closed. This player cannot play the CD-R/RW discs which contains other than CD-DA (or MP3/WMA data). Be sure to observe the instructions of CD-R/RW disc for handling it. Do not leave discs on the following places: Direct sunlight Near car heaters Dirty, dusty and damp areas Seats and dashboards Disc cleaning Use a dry, soft cloth to wipe from the center outward. <Right> <Wrong> Do not attach any seals or labels to your discs. Do not write on the disc label in a heavy pen or ballpoint pen stroke. 62 CQ-HX2083U CQ-HX2083U 63 E N G L I S H 37 Installation Guide WARNING This installation information is designed for experienced installers and is not intended for non-technical individuals. It does not contain warnings or cautions of potential dangers involved in attempting to install this product. Any attempt to install this product in a motor car by anyone other than qualified installer could cause damage to the electrical system and could result in serious personal injury or death. Dashboard Specifications Thickness Min. 7/32z (5. 56 mm) 23/32z (53 mm) 75/32z (182 mm) Identify All Leads The first step in installation is to identify all the car wires you'll use when hooking up your sound system. As you identify each wire, we suggest that you label it using masking tape and a permanent marker. Note: Do not connect the power connector to the stereo unit until you have made all connections. If there are no plastic caps on the stereo hooking wires, insulate all exposed leads with electrical tape until you are ready to use them. Power Lead If your car has a radio or is pre-wired for one: Cut the connector wires one at a time from the plug (leaving the leads as long as possible) so that you can work with individual leads. Installation Hardware No. nut (5 mm·) Rear support strap Tapping screw (5 mm·a16 mm) Mounting bolt (5 mm·) Power connector Trim plate Mounting spring (R) Mounting spring (L) L Diagram Q'ty 1 1 1 1 1 1 1 1 1 2 2 The instructions in these pages will guide you through the remaining steps: (Please refer to the "WARNING" statement above. ) Identify and label the car wires. If you encounter problems, please consult your nearest professional installer. Caution: This unit operates with a 12 V DC negative ground auto battery system only. Before you begin installation, look for the items which are packed with your unit. Panasonic Servicenter List for Service Directory . . . Keep for future reference in case the product needs servicing. Installation Hardware. . . Needed for in-dash installation. If your car has a radio or is pre-wired for one: With the ignition and headlights off, identify the car battery lead by grounding one lead of the test bulb to the chassis and checking the remaining exposed wires from the cut radio connector plug. [. . . ] ; Lock cancel plate Insert the tab end in the outer groove. Security Indicator The security indicator blinks when the removable face plate is removed from the unit. (page 54) Security indicator 1 Panel Removal Alarm This alarm sounds to warn you not to forget to remove the panel before leaving your car. 2 "Click" The function is activated when the security function is on. (page 54) 2 4 Remove the unit pulling with both hands. 68 Caution: This face plate is not waterproof. Do not place the face plate on the dashboard or nearby areas where the temperature rises to high level. Do not touch the contacts on the face plate or on the main unit, since this may result in poor electrical contacts. [. . . ]