User manual PANASONIC CQ-RG131

[. . . ] For repair, please consult your nearest authorized Panasonic Service Center. About Preset Memory The preset memory is cleared to return to the original factor y setting when the power connector or battery is disconnected. 2 CQ-RG131W . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 3 CQ-RG131W E N G L I S H 1 Power and Sound Controls CQ-RG131W LOUD Power Turn the key in the ignition until the accessory indicator lights. Press [PWR] to switch on the power. Volume q Press [VOLj] or [VOLi] to increase or decrease volume. [. . . ] Play starts from the first track. Play Time Disc Number Track Number Note: The cassette, if loaded, should be removed. Otherwise, the CD play will not start. CQ-RG131W Selecting a Disc Press [1] (iDISC) or [2] (DISCj) to select discs in ascending or descending order. LOUD Selecting a Track CQ LOUD Press [TRACK ] once to go to the next track. Press repeatedly to step backward through all the tracks. 10 CQ-RG131W Hold and release CQ Searching a Track LOUD Press and hold [TRACK ] or [TRACK ] for more than 0. 5 second to activate fast forward or reverse through a track. Release [TRACK ] or [TRACK ] to resume the normal CD play from that position. E N G L I S H 8 31W Repeating a Track Press [4] (REPEAT) to repeat the current selection. q The current selection continues to repeat until you press [4] (REPEAT) again. q Random Selection Press [5] (RANDOM) to random selection of music is played from all available CDs. q To turn it off, press [5] (RANDOM) again. q 31W Scanning Tracks Press [3] (SCAN). The track number blinks and the first 10 seconds of each track on the discs play in sequence. q To stop scanning and continue with the current track, press [3] (SCAN) again. q 31W Press and hold Scanning Discs Press and hold [3] (SCAN) for more than 2 seconds. The 1st track of all the discs in the magazine is played for 10 seconds each. To stop the current play of the disc scanning, press and hold [3] (SCAN) for more than 2 seconds again. Error Display Messages Displays when the compact disc is dirty or upside down. Displays when there is no disc in the magazine. 11 CQ-RG131W E N G L I S H 9 Clock Basics (The clock system is 12-hours. ) CQ-RG131W LOUD Press and hold Initial Time Setting Press [DISP]. Be sure to connect the YELLOW lead to the positive terminal (+) of the battery or fuse block (BAT) terminal. Please carefully read the operating and installation instructions of the respective equipment before connecting it to this unit. Supplied Hardwares No. Item Mounting Bolt (5 mm ) Diagram Qty 1 1 Power Connector 1 Rear Support Strap Tapping Screw (5 mm x 16 mm) 1 Dismounting Plate Removable Face Plate Case 1 1 1 13 CQ-RG131W E N G L I S H 11 Installation Guide (continued) Installation Procedures Note: Disconnect the cable from the negative (­) battery terminal. Secure the Mounting Collar . Insert Mounting Collar into the car's dashboard, and bend mounting tabs out with a screwdriver. Secure the rear of the unit. Screwdriver a) Check the electrical connection by referring to this operating instructions. c) Insert the Power Connector Power Connector Unit Mounting Bolt Unit and push it in until "click" is heard. d) Insert the unit into Mounting Collar e) Secure the rear of the unit to the car by either of the two recommended methods as follows. s Using the Rear Support Strap s Using the Rubber Cushion (Option) (If there is an existing Rear Support Bracket on the Fire Wall of Car. ) Cover Mounting Bolt on the rear of the unit with Rubber Cushion (Option), and mount it into the existing Rear Support Bracket. Rear Support Bracket Fire Wall of Car (existing on the car) 3 mm Rubber Cushion Tapping Screw (Option) Hex. Nut Rear Support Strap Mounting Bolt Mounting Collar Mounting Collar Affix one end of the Rear Support Strap Wall of Car, or some other metallic area. to the rear of the unit, and the other end to the Fire Mounting Bolt 3. 14 CQ-RG131W To Remove the Unit a) Remove the trim plate with a screwdriver as shown in the figure (Fig. [. . . ] Fuses with higher capacity ratings, use of any substitute, or connection without a fuse may result in a fire hazard or damage to the unit. If the replacement fuse fails, consult your nearest authorized Panasonic Service Center. E N G L I S H 18 Maintenance To clean the exterior of this unit, use a soft cloth to wipe the surface. Do not use benzine, thinner or any other type of solvents. Specifications General Power Supply Tone Controls Current Consumption Maximum Power Output Power Output Speaker Impedance Dimensions (Main unit) Weight (Main unit) FM Stereo Radio Frequency Range Usable Sensitivity Stereo Separation AM Radio Frequency Range Usable Sensitivity Cassette Player Reproduction System Tape Speed FF/REW Time Frequency Response Wow and Flutter Signal to Noise Ratio : 4-track, 2-program stereo : 4. 76 cm/sec. (C-60) : 35 - 14000 Hz : 0. 12 % (WRMS) : 52 dB : 531 - 1602 kHz : 28 dB/µV (S/N 20 dB) : 87. 5 - 108 MHz : 6 dB/µV (S/N 30 dB) : 35 dB (at 1 kHz) : DC 12 V (11 V - 16 V), Test Voltage 14. 4 V, Negative Ground : Bass; ±12 dB at 100 Hz Treble; ±12 dB at 10 kHz : Less than 2. 5 A (Tape mode, 0. 5 W 4-Speaker) : 40 W x 4 (at 4 ) : 20 W x 4 (DIN45 324, at 4 ) : 4 (4 - 8 acceptable) : 178(W) x 50(H) x 150(D) mm : 1. 6 kg Note: Specifications and the design are subject to possible modification without notice due to improvements. 21 CQ-RG131W CQ-RG131W LOUD 1 [PWR] q [VOLj] j [VOLi] i LOUD q [VOLj] j 0 39 [VOLi] i CQ-RG131W q LOUD [MUTE] MUTE q q CQ-RG131W [MUTE] q LOUD [MUTE](LOUD) 2 q [MUTE](LOUD) 2 20 22 CQ-RG131W [SEL] VOL LOUD BAS TRE FAd BAL 2 [SEL] [VOLi] i LOUD [VOLj ] j d ­12 0 12 ­12 0 12 [SEL] [VOLj] [VOLi] j i LOUD BALANCE R: RL , L: 1 15 q [SEL] [VOLj] [VOLi] j i FADER F: FR , R: 1 15 [ 5 BAS/ VOL TRE/ 2 BAL/ SEL FAd] 23 CQ-RG131W CQ-RG131W LOUD 3 CQ-RG131W CD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]