User manual PANASONIC DMR-EH52

[. . . ] Also available through our Internet is direct shopping for a wide range of finished products, take a browse on our website for further details. Interested in purchasing an extended guarantee?Please contact your dealer or our Customer Support Department on 01344 476540 or customer. care@panasonic. co. uk for more details. Included accessories 1 Remote control (EUR7729KE0) Please check and identify the supplied accessories. These may be subject to change. ) 1 RF coaxial lead (VJA1089) Insert the batteries into the remote control R6/LR6, AA 1 AC mains lead (RJA0044-3C) For use with this unit only. [. . . ] The AV2 or AV4 Scart terminals on Panasonic televisions are compatible with the Q Link functions. BE SURE TO READ THE CAUTION FOR THE AC MAINS LEAD ON PAGE 2 IN THE OPERATING INSTRUCTIONS BEFORE CONNECTION. To household mains socket (AC 220­240 V, 50 Hz) Television's rear panel VHF/UHF RF IN AV IN 1 4 are required connections. Connect in the numbered order. To the aerial AV1 terminal Aerial lead RF coaxial lead Fully wired 21-pin Scart lead If your television is equipped with RGB input capability, by connecting with a fully wired 21-pin Scart lead you can see video using RGB output on this unit ( below). If your television is equipped with Q Link functions, by connecting with a fully wired 21-pin Scart lead you can use these functions ( 70 of Operating Instructions). 1 2 3 4 AC mains lead Connect only after all other connections are complete. VIDEO S VIDEO OUT RF OUT RF IN AV1 (TV) L L Y AUDIO S VIDEO AV4 IN PB PR OPTICAL (PROGRESSIVE/ DIGITAL AUDIO OUT INTERLACE) (PCM/BITSTREAM) R R OUT COMPONENT VIDEO OUT AC IN AV2 (DECODER/EXT) AV4 IN This unit's rear panel Cooling fan Fully wired 21-pin Scart lead DVD/VCR Satellite/Digital terrestrial receiver's rear panel VHF/UHF RF IN To view satellite/digital terrestrial programmes Press [INPUT SELECT] to select the input channel "AV2" for the satellite/digital terrestrial receiver or put this unit in standby mode. To record programmes from satellite/digital terrestrial receiver using "Sky Personal Planner" function 31 of Operating Instructions RGB This refers to the three primary colours of light, red (R), green (G), and blue (B) and also the method of producing video that uses them. By dividing the video signal into the three colours for transmission, noise is reduced for even higher quality images. To record programmes from satellite/digital terrestrial receiver by RGB signals 31 of Operating Instructions -2- Connecting a television with AUDIO/VIDEO terminals and VCR Connecting to the television using the 21-pin Scart leads ( 2) To the aerial Splitter VHF/UHF RF IN 1 4 BE SURE TO READ THE CAUTION FOR THE AC MAINS LEAD ON PAGE 2 IN THE OPERATING INSTRUCTIONS indicates included accessories. Television's rear panel To household mains socket AUDIO IN VIDEO IN (AC 220­240 V, 50 Hz) R L Aerial lead Red White Yellow AC mains lead Connect only after all other connections are complete. RF coaxial lead 1 2 3 Audio/Video cable 4 VIDEO S VIDEO OUT Yellow RF OUT RF IN Yellow L L AV1 (TV) White Red White Red S VIDEO AV4 IN Y PB PR AUDIO OPTICAL (PROGRESSIVE/ DIGITAL AUDIO OUT INTERLACE) (PCM/BITSTREAM) R AV4 IN OUT R COMPONENT VIDEO OUT AC IN AV2 (EXT) This unit's rear panel Audio/Video cable Cooling fan Use a splitter if you also want to connect the aerial to your VCR. Red White Yellow You can also connect with the AV2 terminal on this unit using the 21-pin Scart lead. R L VHF/UHF RF IN AUDIO OUT VIDEO OUT VCR's rear panel Connecting a television with S VIDEO or COMPONENT VIDEO terminals Television's rear panel AUDIO IN VIDEO IN R L S VIDEO IN COMPONENT VIDEO IN AUDIO IN VIDEO IN R L Television's rear panel S VIDEO IN COMPONENT VIDEO IN Red White Yellow S Video cable Red White Yellow Video cable RF OUT Audio/ Video cable Yellow L VIDEO S VIDEO OUT Audio/Video cable RF OUT RF IN VIDEO S VIDEO OUT Yellow L L RF IN L White AUDIO White Y PB PR S VIDEO AV4 IN Y PB PR AUDIO S VIDEO AV4 IN Red R AV4 IN OUT OPTICAL COMPONENT VIDEO OUT (PROGRESSIVE/ INTERLACE) Red R AV4 IN OUT OPTICAL (PROGRESSIVE/ DIGITAL AUDIO OUT INTERLACE) (PCM/BITSTREAM) R COMPONENT VIDEO OUT R DIGITAL AUDIO OUT (PCM/BITSTREAM) COMPONENT VIDEO OUT terminal S VIDEO OUT terminal Connect to S VIDEO IN terminal on the television through a S Video cable. The S VIDEO OUT terminal achieves a more vivid picture than the VIDEO OUT terminal. (Actual results depend on the television. ) Connect to COMPONENT VIDEO IN terminal on the television through video cables. These terminals can be used for either interlace or progressive output ( 69 of Operating Instructions) and provide a purer picture than the S VIDEO OUT terminal. Video output from the component terminal will have no colour during EXT LINK recordings. Use a fully wired 21-pin Scart lead between the TV and the unit when viewing external equipment picture through the AV2 terminal. Change the "AV1 Output" setting in the SETUP menu ( 59 of Operating Instructions) to "Video (with component)" or "S-Video (with component)" after tuning is completed ( 5, 6). If not, the picture will not be in colour. For progressive output ( 22 of Operating Instructions) Note to owners of progressive compatible PAL system televisions ( 6 of Operating Instructions) Component video output Component signal outputs the colour difference signals (PB/PR) and luminance signal (Y) separately in order to achieve high fidelity in reproducing colours. [. . . ] Press [4] and [1], and then repeat steps 6, 7 to enter and store "House No. " and "Postcode". Press [RETURN]. The Owner ID settings screen disappears. DVD/TV To stop partway Press [RETURN]. If the clock setting menu appears Set the clock manually ( 61 of Operating Instructions). To confirm that stations have been tuned correctly ( 60 of Operating Instructions) To restart Preset Download ( 60 of Operating Instructions) If you connect other equipment to AV2 terminal of this unit Change the "AV2 Input" in the SETUP menu to match the connected equipment ( 59 of Operating Instructions). If there is interference or a very poor picture appears on the TV screen Refer to "Removing Interference" on page 21 of Operating Instructions, and perform steps 1, 2 and 4 to stop the RF output. Press [RETURN]. The Owner ID settings screen disappears. To stop partway Press [RETURN]. If the clock setting menu appears Set the clock manually ( 61 of Operating Instructions). To confirm that stations have been tuned correctly ( 60 of Operating Instructions) To restart Auto-Setup ( 60 of Operating Instructions) To enter the satellite/digital terrestrial station's name ( 60 of Operating Instructions) The name of the satellite/digital terrestrial station is not set automatically. [. . . ]