User manual PANASONIC DMR-ES10

[. . . ] · Also available through our Internet is direct shopping for a wide range of finished products, take a browse on our website for further details. Please contact your dealer or our Customer Support Department on 01344 476540 or customer. care@panasonic. co. uk for more details. application at www. panasonic. co. uk. Accessories 1 Remote control (EUR7720KM0) Please check and identify the supplied accessories. [. . . ] · Before connection, turn off all equipment and read the appropriate operating instructions. · Peripheral equipment and optional cables are sold separately unless otherwise indicated. Connecting a television with 21-pin Scart terminal and Satellite/Digital terrestrial receiver indicates included accessories. indicates accessories not included. 1 4 are required connections. Connect in the numbered order. BE SURE TO READ THE CAUTION FOR THE AC MAINS LEAD ON PAGE 2 IN THE OPERATING INSTRUCTIONS BEFORE CONNECTION. Television's rear panel To the aerial VHF/UHF RF IN AV IN To household mains socket (AC 220-240 V, 50 Hz) 1 2 Aerial lead RF coaxial lead 3 Fully wired 21-pin Scart lead (For Q Link functions) AC mains lead Connect only after all other connections are complete. 4 This unit's rear panel AV1 terminal Fully wired 21-pin Scart lead (For External Link functions) If your television is equipped with RGB input capability, by connecting with a fully wired 21-pin Scart lead you can see video using RGB output on this unit ( below). DVD/VCR Satellite/Digital terrestrial receiver's rear panel To view satellite/digital terrestrial programmes · Change the "AV2 Input" setting to match the output from a satellite/digital terrestrial receiver in the SETUP menu ( page 36 of Operating · Press [INPUT SELECT] to select the input channel "A2" for the satellite/digital terrestrial receiver or put this unit in standby mode. To record programmes from satellite receiver using "Sky Personal Planner" function page 21 of Operating Instructions Instructions) after tuning is completed ( page 5, 6). RGB This refers to the three primary colours of light, red (R), green (G), and blue (B) and also the method of producing video that uses them. By dividing the video signal into the three colours for transmission, noise is reduced for even higher quality images. To record programmes from satellite receiver by RGB signals page 21 of Operating Instructions -2- DMR-ES10-EB_QSG-1. fm 3 Connecting a television with AUDIO/VIDEO terminals and VCR BE SURE TO READ THE CAUTION FOR THE AC MAINS LEAD ON PAGE 2 IN THE OPERATING INSTRUCTIONS 1 4 are required connections. To the aerial To household mains socket Television's rear panel (AC 220-240 V, 50 Hz) Splitter VHF/UHF RF IN AUDIO IN VIDEO IN R L indicates included accessories. indicates accessories not included. Red White Yellow Aerial lead 1 2 RF coaxial lead AC mains lead Connect only after all other connections are complete. Audio/Video cable 3 Yellow White Red Yellow White Red 4 Use a splitter if you also want to connect the aerial to your VCR. Audio/Video cable VCR's rear panel Red White Yellow This unit's rear panel VHF/UHF RF IN R L AUDIO OUT VIDEO OUT You can also connect with the AV2 terminal on this unit using the 21-pin Scart lead. Connecting a television with S VIDEO or COMPONENT VIDEO terminals AUDIO IN VIDEO RL IN S VIDEO IN COMPONENT VIDEO IN AUDIO IN VIDEO RL IN S VIDEO IN COMPONENT VIDEO IN Red White Yellow Television's rear panel Red White Yellow Television's rear panel Video cable S Video cable Audio/Video cable Yellow White Red Audio/Video cable Yellow White This unit's rear panel Red This unit's rear panel S VIDEO OUT terminal Connect to S VIDEO IN terminal on the television through a S Video cable. The S VIDEO OUT terminal achieves a more vivid picture than the VIDEO OUT terminal. (Actual results depend on the television. ) COMPONENT VIDEO OUT terminal Connect to COMPONENT VIDEO IN terminals on the television through a video cable. These terminals can be used for either interlace or progressive output ( page 42 of Operating Instructions) and provide a purer picture than the S VIDEO OUT terminal. · Video output from the component terminal will have no colour during EXT LINK recordings. Use a fully wired 21pin Scart lead between the TV and the unit when viewing external equipment picture through the AV2 terminal. ( page 9 of Operating Instructions, Note to owners of progressive compatible PAL system televisions) Component signal outputs the colour difference signals (PB/PR) and luminance signal (Y) separately in order to achieve high fidelity in reproducing colours. If the television is compatible with progressive output, a high quality picture can be output because this unit's component video output terminal outputs a progressive output signal ( page 42 of Operating Instructions). Component video output -3- DMR-ES10-EB_QSG-2. fm 4 For the United Kingdom only Connecting a television with RF socket only and Satellite/Digital terrestrial receiver Connect in the numbered order. If you do not have a Satellite/Digital terrestrial receiver, connect the aerial to RF IN socket of this unit and skip step 3. [. . . ] In step 2, press [0] to select "­ ­". -5- DMR-ES10-EB_QSG-1. fm 6 Auto-Setup (Setup without Q Link functions) · When connecting to a television with the VIDEO OUT, S VIDEO OUT or COMPONENT VIDEO OUT terminal ( page 3). · When connecting to a television that does not have the Q Link functin ( page 42 of Operating Instructions). This unit's Auto-Setup function automatically tunes all available TV stations and synchronizes the time when the TV channel that is broadcasting time and date information is tuned. · When connecting to a television with RF socket only ( page 4). 1 2 DIRECT TV REC AV Turn on the television and select the appropriate AV input to suit the connections to this unit. This takes about 5 minutes. Auto-Setup Ch 1 CH VOLUME For the United Kingdom only Auto-Setup in progress, please wait. [. . . ]